[V1] test_plans/generic_flow_api: add case dual_vlan
Commit Message
move test_dual_vlan in fortville_rss_granularity_config_test_plan.rst to generic_flow_api_test_plan.rst and modify lengacy command.
Signed-off-by: Yan Xia <yanx.xia@intel.com>
---
generic_flow_api_test_plan.diff | 60 +++++++++++++++++++++++++++++++++
1 file changed, 60 insertions(+)
create mode 100644 generic_flow_api_test_plan.diff
new file mode 100644
@@ -0,0 +1,60 @@
+diff --git a/test_plans/generic_flow_api_test_plan.rst b/test_plans/generic_flow_api_test_plan.rst
+index 6a36a63..71f1618 100644
+--- a/test_plans/generic_flow_api_test_plan.rst
++++ b/test_plans/generic_flow_api_test_plan.rst
+@@ -1944,3 +1944,55 @@ Test case: Fortville fdir for l2 mac
+ testpmd> flow create 0 ingress pattern eth dst is 11:11:11:11:11:11 / ipv4 / end actions mark id 3 / rss / end
+
+ Verify second rule can not be created.
++
++Test case: Dual vlan(QinQ)
++=================================
++
++1. config testpmd on DUT
++
++ 1. set up testpmd with Fortville NICs::
++
++ ./testpmd -c 0x1ffff -n 4 -- -i --coremask=0x1fffe --portmask=0x1 --rxq=16 --txq=16 --tx-offloads=0x8fff
++
++ 2. verbose configuration::
++
++ testpmd> set verbose 8
++
++ 3. PMD fwd only receive the packets::
++
++ testpmd> set fwd rxonly
++
++ 4. set extend on::
++
++ testpmd> vlan set extend on <port_id>
++
++ 5. create rule::
++
++ testpmd> flow create 0 ingress pattern eth / end actions rss types l2-payload end queues end func toeplitz / end
++
++ 6. start packet receive::
++
++ testpmd> start
++
++
++2. using scapy to send packets with dual vlan (QinQ) on tester::
++
++
++ sendp([Ether(dst="68:05:ca:30:6a:f8")/Dot1Q(id=0x8100,vlan=1)/Dot1Q(id=0x8100,vlan=2,type=0xaaaa)/Raw(load="x"*60)], iface=ttester_itf)
++
++ then got hash value and queue value that output from the testpmd on DUT.
++
++3. create flow rss type s-vlan c-vlan by testpmd on dut::
++
++
++ testpmd> flow create 0 ingress pattern eth / end actions rss types s-vlan c-vlan end key_len 0 queues end / end
++
++ 1). send packet as step 2, got hash value and queue value that output from the testpmd on DUT, the value should be
++ different with the values in step 2.
++
++
++ 2). send packet as step 2 with changed ovlan id, got hash value and queue value that output from the testpmd on DUT, the value should be
++ different with the values in step 2 & step 1).
++
++ 3). send packet as step 2 with changed ivlan id, got hash value and queue value that output from the testpmd on DUT, the value should be
++ different with the values in step 2 & step 1) & step 2).