[v4,6/8] bus/dpaa: remove unused code
Checks
Commit Message
From: Gagandeep Singh <g.singh@nxp.com>
The slow poll code is not being used in DPDK DPAA driver sub-system.
Signed-off-by: Gagandeep Singh <g.singh@nxp.com>
Signed-off-by: Vanshika Shukla <vanshika.shukla@nxp.com>
---
drivers/bus/dpaa/base/qbman/qman.c | 31 -----------------------------
drivers/bus/dpaa/include/fsl_qman.h | 31 -----------------------------
drivers/bus/dpaa/version.map | 1 -
3 files changed, 63 deletions(-)
@@ -69,7 +69,6 @@ struct qman_portal {
/* interrupt sources processed by portal_isr(), configurable */
unsigned long irq_sources;
u32 use_eqcr_ci_stashing;
- u32 slowpoll; /* only used when interrupts are off */
/* only 1 volatile dequeue at a time */
struct qman_fq *vdqcr_owned;
u32 sdqcr;
@@ -569,7 +568,6 @@ qman_init_portal(struct qman_portal *portal,
INIT_LIST_HEAD(&portal->cgr_cbs);
spin_lock_init(&portal->cgr_lock);
portal->bits = 0;
- portal->slowpoll = 0;
portal->sdqcr = QM_SDQCR_SOURCE_CHANNELS | QM_SDQCR_COUNT_UPTO3 |
QM_SDQCR_DEDICATED_PRECEDENCE | QM_SDQCR_TYPE_PRIO_QOS |
QM_SDQCR_TOKEN_SET(0xab) | QM_SDQCR_CHANNELS_DEDICATED;
@@ -1370,35 +1368,6 @@ void qman_dqrr_consume(struct qman_fq *fq,
qm_dqrr_next(&p->p);
}
-int qman_poll_dqrr(unsigned int limit)
-{
- struct qman_portal *p = get_affine_portal();
- int ret;
-
- ret = __poll_portal_fast(p, limit);
- return ret;
-}
-
-void qman_poll(void)
-{
- struct qman_portal *p = get_affine_portal();
-
- if ((~p->irq_sources) & QM_PIRQ_SLOW) {
- if (!(p->slowpoll--)) {
- u32 is = qm_isr_status_read(&p->p) & ~p->irq_sources;
- u32 active = __poll_portal_slow(p, is);
-
- if (active) {
- qm_isr_status_clear(&p->p, active);
- p->slowpoll = SLOW_POLL_BUSY;
- } else
- p->slowpoll = SLOW_POLL_IDLE;
- }
- }
- if ((~p->irq_sources) & QM_PIRQ_DQRI)
- __poll_portal_fast(p, FSL_QMAN_POLL_LIMIT);
-}
-
void qman_stop_dequeues(void)
{
struct qman_portal *p = get_affine_portal();
@@ -1429,37 +1429,6 @@ __rte_internal
void qman_dqrr_consume(struct qman_fq *fq,
struct qm_dqrr_entry *dq);
-/**
- * qman_poll_dqrr - process DQRR (fast-path) entries
- * @limit: the maximum number of DQRR entries to process
- *
- * Use of this function requires that DQRR processing not be interrupt-driven.
- * Ie. the value returned by qman_irqsource_get() should not include
- * QM_PIRQ_DQRI. If the current CPU is sharing a portal hosted on another CPU,
- * this function will return -EINVAL, otherwise the return value is >=0 and
- * represents the number of DQRR entries processed.
- */
-__rte_internal
-int qman_poll_dqrr(unsigned int limit);
-
-/**
- * qman_poll
- *
- * Dispatcher logic on a cpu can use this to trigger any maintenance of the
- * affine portal. There are two classes of portal processing in question;
- * fast-path (which involves demuxing dequeue ring (DQRR) entries and tracking
- * enqueue ring (EQCR) consumption), and slow-path (which involves EQCR
- * thresholds, congestion state changes, etc). This function does whatever
- * processing is not triggered by interrupts.
- *
- * Note, if DQRR and some slow-path processing are poll-driven (rather than
- * interrupt-driven) then this function uses a heuristic to determine how often
- * to run slow-path processing - as slow-path processing introduces at least a
- * minimum latency each time it is run, whereas fast-path (DQRR) processing is
- * close to zero-cost if there is no work to be done.
- */
-void qman_poll(void);
-
/**
* qman_stop_dequeues - Stop h/w dequeuing to the s/w portal
*
@@ -82,7 +82,6 @@ INTERNAL {
qman_irqsource_remove;
qman_modify_cgr;
qman_oos_fq;
- qman_poll_dqrr;
qman_portal_dequeue;
qman_portal_poll_rx;
qman_query_fq_frm_cnt;