[v4,2/3] examples/l3fwd: print port bdf when adding routes
Checks
Commit Message
From: Pavan Nikhilesh <pbhagavatula@marvell.com>
Since the number of Ethernet ports have gone up, print the pci bdf along
with the routes.
This is also helpful for cases where allow listing order is not honored.
Signed-off-by: Pavan Nikhilesh <pbhagavatula@marvell.com>
---
examples/l3fwd/l3fwd_fib.c | 16 ++++++++++------
examples/l3fwd/l3fwd_lpm.c | 9 ++++++---
2 files changed, 16 insertions(+), 9 deletions(-)
@@ -439,6 +439,7 @@ setup_fib(const int socketid)
/* Populate the fib ipv4 table. */
for (i = 0; i < RTE_DIM(ipv4_l3fwd_route_array); i++) {
+ struct rte_eth_dev_info dev_info;
struct in_addr in;
/* Skip unused ports. */
@@ -446,6 +447,8 @@ setup_fib(const int socketid)
enabled_port_mask) == 0)
continue;
+ rte_eth_dev_info_get(ipv4_l3fwd_route_array[i].if_out,
+ &dev_info);
ret = rte_fib_add(ipv4_l3fwd_fib_lookup_struct[socketid],
ipv4_l3fwd_route_array[i].ip,
ipv4_l3fwd_route_array[i].depth,
@@ -459,13 +462,14 @@ setup_fib(const int socketid)
in.s_addr = htonl(ipv4_l3fwd_route_array[i].ip);
if (inet_ntop(AF_INET, &in, abuf, sizeof(abuf)) != NULL) {
- printf("FIB: Adding route %s / %d (%d)\n",
- abuf,
- ipv4_l3fwd_route_array[i].depth,
- ipv4_l3fwd_route_array[i].if_out);
+ printf("FIB: Adding route %s / %d (%d) [%s]\n", abuf,
+ ipv4_l3fwd_route_array[i].depth,
+ ipv4_l3fwd_route_array[i].if_out,
+ dev_info.device->name);
} else {
- printf("FIB: IPv4 route added to port %d\n",
- ipv4_l3fwd_route_array[i].if_out);
+ printf("FIB: IPv4 route added to port %d [%s]\n",
+ ipv4_l3fwd_route_array[i].if_out,
+ dev_info.device->name);
}
}
/* >8 End of setup fib. */
@@ -451,6 +451,7 @@ setup_lpm(const int socketid)
/* populate the LPM table */
for (i = 0; i < RTE_DIM(ipv4_l3fwd_route_array); i++) {
+ struct rte_eth_dev_info dev_info;
struct in_addr in;
/* skip unused ports */
@@ -458,6 +459,8 @@ setup_lpm(const int socketid)
enabled_port_mask) == 0)
continue;
+ rte_eth_dev_info_get(ipv4_l3fwd_route_array[i].if_out,
+ &dev_info);
ret = rte_lpm_add(ipv4_l3fwd_lpm_lookup_struct[socketid],
ipv4_l3fwd_route_array[i].ip,
ipv4_l3fwd_route_array[i].depth,
@@ -470,10 +473,10 @@ setup_lpm(const int socketid)
}
in.s_addr = htonl(ipv4_l3fwd_route_array[i].ip);
- printf("LPM: Adding route %s / %d (%d)\n",
+ printf("LPM: Adding route %s / %d (%d) [%s]\n",
inet_ntop(AF_INET, &in, abuf, sizeof(abuf)),
- ipv4_l3fwd_route_array[i].depth,
- ipv4_l3fwd_route_array[i].if_out);
+ ipv4_l3fwd_route_array[i].depth,
+ ipv4_l3fwd_route_array[i].if_out, dev_info.device->name);
}
/* create the LPM6 table */