diff mbox series

[3/4] net/bnxt: fix enabling autoneg on Whitney+

Message ID 20210609031332.16739-4-kalesh-anakkur.purayil@broadcom.com (mailing list archive)
State Accepted, archived
Delegated to: Ajit Khaparde
Headers
Series bnxt fixes |

Checks

Context Check Description
ci/checkpatch success coding style OK

Commit Message

Kalesh A P June 9, 2021, 3:13 a.m. UTC 
  From: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>

Driver should enable autoneg on a port if FW supports it.
Because of a wrong check, driver is not enabling autoneg
on a port after setting forced speed on Whitney+.

Fixes: 7bc8e9a227cc ("net/bnxt: support async link notification")
Cc: stable@dpdk.org

Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
---
 drivers/net/bnxt/bnxt_hwrm.c | 18 +++++++++---------
 1 file changed, 9 insertions(+), 9 deletions(-)
diff mbox series

Patch

diff --git a/drivers/net/bnxt/bnxt_hwrm.c b/drivers/net/bnxt/bnxt_hwrm.c
index 5d34081..451a65d 100644
--- a/drivers/net/bnxt/bnxt_hwrm.c
+++ b/drivers/net/bnxt/bnxt_hwrm.c
@@ -1489,6 +1489,7 @@  static int bnxt_hwrm_port_phy_qcfg(struct bnxt *bp,
 
 	link_info->support_speeds = rte_le_to_cpu_16(resp->support_speeds);
 	link_info->auto_link_speed = rte_le_to_cpu_16(resp->auto_link_speed);
+	link_info->auto_link_speed_mask = rte_le_to_cpu_16(resp->auto_link_speed_mask);
 	link_info->preemphasis = rte_le_to_cpu_32(resp->preemphasis);
 	link_info->force_link_speed = rte_le_to_cpu_16(resp->force_link_speed);
 	link_info->phy_ver[0] = resp->phy_maj;
@@ -1543,6 +1544,12 @@  int bnxt_hwrm_port_phy_qcaps(struct bnxt *bp)
 
 	HWRM_UNLOCK();
 
+	/* Older firmware does not have supported_auto_speeds, so assume
+	 * that all supported speeds can be autonegotiated.
+	 */
+	if (link_info->auto_link_speed_mask && !link_info->support_auto_speeds)
+		link_info->support_auto_speeds = link_info->support_speeds;
+
 	return 0;
 }
 
@@ -3243,15 +3250,8 @@  int bnxt_set_hwrm_link_config(struct bnxt *bp, bool link_up)
 	speed = bnxt_parse_eth_link_speed(dev_conf->link_speeds,
 					  bp->link_info->link_signal_mode);
 	link_req.phy_flags = HWRM_PORT_PHY_CFG_INPUT_FLAGS_RESET_PHY;
-	/* Autoneg can be done only when the FW allows.
-	 * When user configures fixed speed of 40G and later changes to
-	 * any other speed, auto_link_speed/force_link_speed is still set
-	 * to 40G until link comes up at new speed.
-	 */
-	if (autoneg == 1 &&
-	    !(!BNXT_CHIP_P5(bp) &&
-	      (bp->link_info->auto_link_speed ||
-	       bp->link_info->force_link_speed))) {
+	/* Autoneg can be done only when the FW allows. */
+	if (autoneg == 1 && bp->link_info->support_auto_speeds) {
 		link_req.phy_flags |=
 				HWRM_PORT_PHY_CFG_INPUT_FLAGS_RESTART_AUTONEG;
 		link_req.auto_link_speed_mask =