diff mbox series

[v2,6/9] net/hns3: set max scheduling rate based on actual board

Message ID 20200929120117.50394-7-huwei013@chinasoftinc.com (mailing list archive)
State Accepted, archived
Delegated to: Ferruh Yigit
Headers show
Series updates and fixes for hns3 PMD driver | expand

Checks

Context Check Description
ci/checkpatch success coding style OK

Commit Message

Wei Hu (Xavier) Sept. 29, 2020, 12:01 p.m. UTC
From: Huisong Li <lihuisong@huawei.com>

Currently, max scheduling rates configuration of pg, pri and port are set
to 100000Mbps, which is the maximum bandwidth of hns3 network engine with
revision_id equals 0x21. However, max scheduling rate configuration should
be set to hardware based on the actual hardware board environment.

The max_tm_rate in struct hns3_hw, meaning the rate, is obtained from
firmware. So we should use the variable to configure the max scheduling
rate.

Signed-off-by: Huisong Li <lihuisong@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
---
 drivers/net/hns3/hns3_dcb.c | 12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)
diff mbox series

Patch

diff --git a/drivers/net/hns3/hns3_dcb.c b/drivers/net/hns3/hns3_dcb.c
index 857e79e..27ae014 100644
--- a/drivers/net/hns3/hns3_dcb.c
+++ b/drivers/net/hns3/hns3_dcb.c
@@ -62,9 +62,9 @@  hns3_shaper_para_calc(struct hns3_hw *hw, uint32_t ir, uint8_t shaper_level,
 		return -EINVAL;
 	}
 
-	if (ir > HNS3_ETHER_MAX_RATE) {
-		hns3_err(hw, "rate(%d) exceeds the rate driver supported "
-			 "HNS3_ETHER_MAX_RATE(%d)", ir, HNS3_ETHER_MAX_RATE);
+	if (ir > hw->max_tm_rate) {
+		hns3_err(hw, "rate(%d) exceeds the max rate(%d) driver "
+			 "supported.", ir, hw->max_tm_rate);
 		return -EINVAL;
 	}
 
@@ -100,7 +100,7 @@  hns3_shaper_para_calc(struct hns3_hw *hw, uint32_t ir, uint8_t shaper_level,
 		 * ir_calc gets minimum value when tick is the maximum value.
 		 * At the same time, value of ir_u_calc can only be increased up
 		 * to eight after the while loop if the value of ir is equal
-		 * to HNS3_ETHER_MAX_RATE.
+		 * to hw->max_tm_rate.
 		 */
 		uint32_t numerator;
 		do {
@@ -736,7 +736,7 @@  hns3_dcb_info_init(struct hns3_hw *hw)
 		hw->dcb_info.pg_dwrr[i] = i ? 0 : BW_MAX_PERCENT;
 		hw->dcb_info.pg_info[i].pg_id = i;
 		hw->dcb_info.pg_info[i].pg_sch_mode = HNS3_SCH_MODE_DWRR;
-		hw->dcb_info.pg_info[i].bw_limit = HNS3_ETHER_MAX_RATE;
+		hw->dcb_info.pg_info[i].bw_limit = hw->max_tm_rate;
 
 		if (i != 0)
 			continue;
@@ -1405,7 +1405,7 @@  hns3_dcb_info_cfg(struct hns3_adapter *hns)
 	hw->dcb_info.pg_dwrr[0] = BW_MAX_PERCENT;
 	hw->dcb_info.pg_info[0].pg_id = 0;
 	hw->dcb_info.pg_info[0].pg_sch_mode = HNS3_SCH_MODE_DWRR;
-	hw->dcb_info.pg_info[0].bw_limit = HNS3_ETHER_MAX_RATE;
+	hw->dcb_info.pg_info[0].bw_limit = hw->max_tm_rate;
 	hw->dcb_info.pg_info[0].tc_bit_map = hw->hw_tc_map;
 
 	/* Each tc has same bw for valid tc by default */