[5/6] net/enic: add VLAN and csum offloads to simple Tx handler
Checks
Commit Message
From: Hyong Youb Kim <hyonkim@cisco.com>
Currently the simple Tx handler supports no offloads, which makes it
usable only for a small number of benchmarks. Add vlan and checksum
offloads to the handler, as cycles/packet increases only by about 3
cycles, and applications commonly use those offloads.
Signed-off-by: Hyong Youb Kim <hyonkim@cisco.com>
Reviewed-by: John Daley <johndale@cisco.com>
---
drivers/net/enic/enic_main.c | 14 +++++++++++---
drivers/net/enic/enic_rxtx.c | 21 +++++++++++++++++++++
2 files changed, 32 insertions(+), 3 deletions(-)
@@ -534,6 +534,7 @@ int enic_enable(struct enic *enic)
unsigned int index;
int err;
struct rte_eth_dev *eth_dev = enic->rte_dev;
+ uint64_t simple_tx_offloads;
eth_dev->data->dev_link.link_speed = vnic_dev_port_speed(enic->vdev);
eth_dev->data->dev_link.link_duplex = ETH_LINK_FULL_DUPLEX;
@@ -572,10 +573,17 @@ int enic_enable(struct enic *enic)
}
/*
- * Use the simple TX handler if possible. All offloads must be
- * disabled.
+ * Use the simple TX handler if possible. Only checksum offloads
+ * and vlan insertion are supported.
*/
- if (eth_dev->data->dev_conf.txmode.offloads == 0) {
+ simple_tx_offloads = enic->tx_offload_capa &
+ (DEV_TX_OFFLOAD_OUTER_IPV4_CKSUM |
+ DEV_TX_OFFLOAD_VLAN_INSERT |
+ DEV_TX_OFFLOAD_IPV4_CKSUM |
+ DEV_TX_OFFLOAD_UDP_CKSUM |
+ DEV_TX_OFFLOAD_TCP_CKSUM);
+ if ((eth_dev->data->dev_conf.txmode.offloads &
+ ~simple_tx_offloads) == 0) {
PMD_INIT_LOG(DEBUG, " use the simple tx handler");
eth_dev->tx_pkt_burst = &enic_simple_xmit_pkts;
for (index = 0; index < enic->wq_count; index++)
@@ -842,12 +842,33 @@ static void enqueue_simple_pkts(struct rte_mbuf **pkts,
struct enic *enic)
{
struct rte_mbuf *p;
+ uint16_t mss;
while (n) {
n--;
p = *pkts++;
desc->address = p->buf_iova + p->data_off;
desc->length = p->pkt_len;
+ /* VLAN insert */
+ desc->vlan_tag = p->vlan_tci;
+ desc->header_length_flags &=
+ ((1 << WQ_ENET_FLAGS_EOP_SHIFT) |
+ (1 << WQ_ENET_FLAGS_CQ_ENTRY_SHIFT));
+ if (p->ol_flags & PKT_TX_VLAN) {
+ desc->header_length_flags |=
+ 1 << WQ_ENET_FLAGS_VLAN_TAG_INSERT_SHIFT;
+ }
+ /*
+ * Checksum offload. We use WQ_ENET_OFFLOAD_MODE_CSUM, which
+ * is 0, so no need to set offload_mode.
+ */
+ mss = 0;
+ if (p->ol_flags & PKT_TX_IP_CKSUM)
+ mss |= ENIC_CALC_IP_CKSUM << WQ_ENET_MSS_SHIFT;
+ if (p->ol_flags & PKT_TX_L4_MASK)
+ mss |= ENIC_CALC_TCP_UDP_CKSUM << WQ_ENET_MSS_SHIFT;
+ desc->mss_loopback = mss;
+
/*
* The app should not send oversized
* packets. tx_pkt_prepare includes a check as