[02/11] net/mlx5: limit LRO size to the maximum Rx packet
Checks
Commit Message
The field max_rx_pkt_len in Rx configuration indicates the maximum size
for Rx packet to be received.
There was no any field to indicate the maximum size of LRO packet to be
received by the application.
Assuming the user configures max_rx_pkt_len as the maximum LRO packet
length when LRO is configured on the port, the PMD limits the maximum
LRO packet size received from HW to be max_rx_pkt_len.
Signed-off-by: Matan Azrad <matan@mellanox.com>
Acked-by: Viacheslav Ovsiienko <viacheslavo@mellanox.com>
---
drivers/net/mlx5/mlx5_prm.h | 5 +++++
drivers/net/mlx5/mlx5_rxq.c | 38 ++++++++++++++++++--------------------
2 files changed, 23 insertions(+), 20 deletions(-)
@@ -1465,6 +1465,11 @@ enum {
MLX5_TIRC_SELF_LB_BLOCK_BLOCK_MULTICAST = 0x2,
};
+enum {
+ MLX5_LRO_MAX_MSG_SIZE_START_FROM_L4 = 0x0,
+ MLX5_LRO_MAX_MSG_SIZE_START_FROM_L2 = 0x1,
+};
+
struct mlx5_ifc_tirc_bits {
u8 reserved_at_0[0x20];
u8 disp_type[0x4];
@@ -1543,37 +1543,35 @@ struct mlx5_rxq_obj *
return 0;
}
+#define MLX5_MAX_LRO_SIZE (UINT8_MAX * 256u)
+#define MLX5_MAX_TCP_HDR_OFFSET ((unsigned int)(sizeof(struct rte_ether_hdr) + \
+ sizeof(struct rte_vlan_hdr) * 2 + \
+ sizeof(struct rte_ipv6_hdr)))
/**
* Adjust the maximum LRO massage size.
- * LRO massage is contained in the MPRQ strides.
- * While the LRO massage size cannot be bigger than 65280 according to the
- * PRM, the strides which contain it may be bigger.
- * Adjust the maximum LRO massage size to avoid the above option.
*
* @param dev
* Pointer to Ethernet device.
- * @param strd_n
- * Number of strides per WQE..
- * @param strd_sz
- * The stride size.
+ * @param max_lro_size
+ * The maximum size for LRO packet.
*/
static void
-mlx5_max_lro_msg_size_adjust(struct rte_eth_dev *dev, uint32_t strd_n,
- uint32_t strd_sz)
+mlx5_max_lro_msg_size_adjust(struct rte_eth_dev *dev, uint32_t max_lro_size)
{
struct mlx5_priv *priv = dev->data->dev_private;
- uint32_t max_buf_len = strd_sz * strd_n;
- if (max_buf_len > (uint64_t)UINT16_MAX)
- max_buf_len = RTE_ALIGN_FLOOR((uint32_t)UINT16_MAX, strd_sz);
- max_buf_len /= 256;
- max_buf_len = RTE_MIN(max_buf_len, (uint32_t)UINT8_MAX);
- assert(max_buf_len);
+ if (priv->config.hca_attr.lro_max_msg_sz_mode ==
+ MLX5_LRO_MAX_MSG_SIZE_START_FROM_L4 && max_lro_size >
+ MLX5_MAX_TCP_HDR_OFFSET)
+ max_lro_size -= MLX5_MAX_TCP_HDR_OFFSET;
+ max_lro_size = RTE_MIN(max_lro_size, MLX5_MAX_LRO_SIZE);
+ assert(max_lro_size >= 256u);
+ max_lro_size /= 256u;
if (priv->max_lro_msg_size)
priv->max_lro_msg_size =
- RTE_MIN((uint32_t)priv->max_lro_msg_size, max_buf_len);
+ RTE_MIN((uint32_t)priv->max_lro_msg_size, max_lro_size);
else
- priv->max_lro_msg_size = max_buf_len;
+ priv->max_lro_msg_size = max_lro_size;
}
/**
@@ -1671,8 +1669,8 @@ struct mlx5_rxq_ctrl *
tmpl->rxq.strd_headroom_en = strd_headroom_en;
tmpl->rxq.mprq_max_memcpy_len = RTE_MIN(mb_len -
RTE_PKTMBUF_HEADROOM, config->mprq.max_memcpy_len);
- mlx5_max_lro_msg_size_adjust(dev, (1 << tmpl->rxq.strd_num_n),
- (1 << tmpl->rxq.strd_sz_n));
+ mlx5_max_lro_msg_size_adjust(dev, RTE_MIN(max_rx_pkt_len,
+ (1u << tmpl->rxq.strd_num_n) * (1u << tmpl->rxq.strd_sz_n)));
DRV_LOG(DEBUG,
"port %u Rx queue %u: Multi-Packet RQ is enabled"
" strd_num_n = %u, strd_sz_n = %u",