[09/11] net/mlx5: handle LRO packets in regular Rx queue
Checks
Commit Message
When LRO offload is configured in Rx queue, the HW may coalesce TCP
packets from same TCP connection into single packet.
In this case the SW should fix the relevant packet headers because
the HW doesn't update them according to the new created packet
characteristics but provides the update values in the CQE.
Add update header code to the regular Rx burst function to support LRO
feature.
Make sure the first mbuf has enough space to include each TCP header,
otherwise the header update may cross mbufs what complicates the
operation too match.
Signed-off-by: Matan Azrad <matan@mellanox.com>
Acked-by: Viacheslav Ovsiienko <viacheslavo@mellanox.com>
---
doc/guides/nics/mlx5.rst | 4 +++-
drivers/net/mlx5/mlx5_rxq.c | 20 +++++++++++++++++---
drivers/net/mlx5/mlx5_rxtx.c | 17 +++++++++++++++++
3 files changed, 37 insertions(+), 4 deletions(-)
@@ -165,7 +165,9 @@ Limitations
- LRO:
- - scatter_fcs is disabled when LRO is configured.
+ - KEEP_CRC offload cannot be supported with LRO.
+ - The first mbuf length, without head-room, must be big enough to include the
+ TCP header (122B).
Statistics
----------
@@ -1541,6 +1541,11 @@ struct mlx5_rxq_obj *
#define MLX5_MAX_TCP_HDR_OFFSET ((unsigned int)(sizeof(struct rte_ether_hdr) + \
sizeof(struct rte_vlan_hdr) * 2 + \
sizeof(struct rte_ipv6_hdr)))
+#define MAX_TCP_OPTION_SIZE 40u
+#define MLX5_MAX_LRO_HEADER_FIX ((unsigned int)(MLX5_MAX_TCP_HDR_OFFSET + \
+ sizeof(struct rte_tcp_hdr) + \
+ MAX_TCP_OPTION_SIZE))
+
/**
* Adjust the maximum LRO massage size.
*
@@ -1607,6 +1612,7 @@ struct mlx5_rxq_ctrl *
unsigned int non_scatter_min_mbuf_size = max_rx_pkt_len +
RTE_PKTMBUF_HEADROOM;
unsigned int max_lro_size = 0;
+ unsigned int first_mb_free_size = mb_len - RTE_PKTMBUF_HEADROOM;
if (non_scatter_min_mbuf_size > mb_len && !(offloads &
DEV_RX_OFFLOAD_SCATTER)) {
@@ -1670,8 +1676,8 @@ struct mlx5_rxq_ctrl *
config->mprq.min_stride_size_n);
tmpl->rxq.strd_shift_en = MLX5_MPRQ_TWO_BYTE_SHIFT;
tmpl->rxq.strd_headroom_en = strd_headroom_en;
- tmpl->rxq.mprq_max_memcpy_len = RTE_MIN(mb_len -
- RTE_PKTMBUF_HEADROOM, config->mprq.max_memcpy_len);
+ tmpl->rxq.mprq_max_memcpy_len = RTE_MIN(first_mb_free_size,
+ config->mprq.max_memcpy_len);
max_lro_size = RTE_MIN(max_rx_pkt_len,
(1u << tmpl->rxq.strd_num_n) *
(1u << tmpl->rxq.strd_sz_n));
@@ -1680,13 +1686,21 @@ struct mlx5_rxq_ctrl *
" strd_num_n = %u, strd_sz_n = %u",
dev->data->port_id, idx,
tmpl->rxq.strd_num_n, tmpl->rxq.strd_sz_n);
- } else if (max_rx_pkt_len <= (mb_len - RTE_PKTMBUF_HEADROOM)) {
+ } else if (max_rx_pkt_len <= first_mb_free_size) {
tmpl->rxq.sges_n = 0;
max_lro_size = max_rx_pkt_len;
} else if (offloads & DEV_RX_OFFLOAD_SCATTER) {
unsigned int size = non_scatter_min_mbuf_size;
unsigned int sges_n;
+ if (mlx5_lro_on(dev) && first_mb_free_size <
+ MLX5_MAX_LRO_HEADER_FIX) {
+ DRV_LOG(ERR, "Not enough space in the first segment(%u)"
+ " to include the max header size(%u) for LRO",
+ first_mb_free_size, MLX5_MAX_LRO_HEADER_FIX);
+ rte_errno = ENOTSUP;
+ goto error;
+ }
/*
* Determine the number of SGEs needed for a full packet
* and round it to the next power of two.
@@ -107,6 +107,16 @@ enum mlx5_txcmp_code {
mlx5_queue_state_modify(struct rte_eth_dev *dev,
struct mlx5_mp_arg_queue_state_modify *sm);
+static inline void
+mlx5_lro_update_tcp_hdr(struct rte_tcp_hdr *restrict tcp,
+ volatile struct mlx5_cqe *restrict cqe,
+ uint32_t phcsum);
+
+static inline void
+mlx5_lro_update_hdr(uint8_t *restrict padd,
+ volatile struct mlx5_cqe *restrict cqe,
+ uint32_t len);
+
uint32_t mlx5_ptype_table[] __rte_cache_aligned = {
[0xff] = RTE_PTYPE_ALL_MASK, /* Last entry for errored packet. */
};
@@ -1323,6 +1333,13 @@ enum mlx5_txcmp_code {
if (rxq->crc_present)
len -= RTE_ETHER_CRC_LEN;
PKT_LEN(pkt) = len;
+ if (cqe->lro_num_seg > 1) {
+ mlx5_lro_update_hdr
+ (rte_pktmbuf_mtod(pkt, uint8_t *), cqe,
+ len);
+ pkt->ol_flags |= PKT_RX_LRO;
+ pkt->tso_segsz = len / cqe->lro_num_seg;
+ }
}
DATA_LEN(rep) = DATA_LEN(seg);
PKT_LEN(rep) = PKT_LEN(seg);