diff --git a/doc/guides/testpmd_app_ug/testpmd_funcs.rst b/doc/guides/testpmd_app_ug/testpmd_funcs.rst
index 3b62118..2e64a3a 100644
--- a/doc/guides/testpmd_app_ug/testpmd_funcs.rst
+++ b/doc/guides/testpmd_app_ug/testpmd_funcs.rst
@@ -435,20 +435,6 @@ Remove a VLAN ID, from the set of VLAN identifiers filtered for VF(s) for port I
 
 rx_vlan rm (vlan_id) port (port_id) vf (vf_mask)
 
-tx_rate (for Queue)
-~~~~~~~~~~~~~~~~~~~
-
-Set TX rate limitation for queue of a port ID:
-
-set port (port_id) queue (queue_id) rate (rate_value)
-
-tx_rate (for VF)
-~~~~~~~~~~~~~~~~
-
-Set TX rate limitation for queues in VF of a port ID:
-
-set port (port_id) vf (vf_id) rate (rate_value) queue_mask (queue_mask)
-
 rx_vlan set tpid
 ~~~~~~~~~~~~~~~~
 
@@ -698,6 +684,20 @@ The available receive modes are:
 
 *  MPE: accepts all multicast packets
 
+set port - tx_rate (for Queue)
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Set TX rate limitation for queue of a port ID:
+
+set port (port_id) queue (queue_id) rate (rate_value)
+
+set port - tx_rate (for VF)
+~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Set TX rate limitation for queues in VF of a port ID:
+
+set port (port_id) vf (vf_id) rate (rate_value) queue_mask (queue_mask)
+
 set port - mirror rule
 ~~~~~~~~~~~~~~~~~~~~~~
 
@@ -764,884 +764,889 @@ Show the bypass configuration for a bypass enabled NIC using the lowest port on
 
 show bypass config (port_id)
 
-add_ethertype_filter
-~~~~~~~~~~~~~~~~~~~~
+set link up
+~~~~~~~~~~~
 
-Add a L2 Ethertype filter, which identify packets by their L2 Ethertype mainly assign them to a receive queue.
+Set link up for a port.
 
-add_ethertype_filter (port_id) ethertype (eth_value) priority (enable|disable) (pri_value) queue (queue_id) index (idx)
+set link-up port (port id)
 
-The available information parameters are:
+set link down
+~~~~~~~~~~~~~
 
-*   port_id:  the port which the Ethertype filter assigned on.
+Set link down for a port.
 
-*   eth_value: the EtherType value want to match,
-    for example 0x0806 for ARP packet. 0x0800 (IPv4) and 0x86DD (IPv6) are invalid.
+set link-down port (port id)
 
-*   enable: user priority participates in the match.
+Port Functions
+--------------
 
-*   disable: user priority doesn't participate in the match.
+The following sections show functions for configuring ports.
 
-*   pri_value: user priority value that want to match.
+.. note::
 
-*   queue_id : The receive queue associated with this EtherType filter
+    Port configuration changes only become active when forwarding is started/restarted.
 
-*   index: the index of this EtherType filter
+port start
+~~~~~~~~~~
 
-Example:
+Start all ports or a specific port:
 
-.. code-block:: console
+port start (port_id|all)
 
-    testpmd> add_ethertype_filter 0 ethertype 0x0806 priority disable 0 queue 3 index 0
-    Assign ARP packet to receive queue 3
+port stop
+~~~~~~~~~
 
-remove_ethertype_filter
-~~~~~~~~~~~~~~~~~~~~~~~
+Stop all ports or a specific port:
 
-Remove a L2 Ethertype filter
+port stop (port_id|all)
 
-remove_ethertype_filter (port_id) index (idx)
+port close
+~~~~~~~~~~
 
-get_ethertype_filter
-~~~~~~~~~~~~~~~~~~~~
+Close all ports or a specific port:
 
-Get and display a L2 Ethertype filter
+port close (port_id|all)
 
-get_ethertype_filter (port_id) index (idx)
+port start/stop queue
+~~~~~~~~~~~~~~~~~~~~
 
-Example:
+Start/stop a rx/tx queue on a specific port:
 
-.. code-block:: console
+port (port_id) (rxq|txq) (queue_id) (start|stop)
 
-    testpmd> get_ethertype_filter 0 index 0
+Only take effect when port is started.
 
-    filter[0]:
-        ethertype: 0x0806
-        priority: disable, 0
-        queue: 3
+port config - speed
+~~~~~~~~~~~~~~~~~~~
 
-add_2tuple_filter
-~~~~~~~~~~~~~~~~~
+Set the speed and duplex mode for all ports or a specific port:
 
-Add a 2-tuple filter,
-which identify packets by specific protocol and destination TCP/UDP port
-and forwards packets into one of the receive queues.
+port config (port_id|all) speed (10|100|1000|10000|auto) duplex (half|full|auto)
 
-add_2tuple_filter (port_id) protocol (pro_value) (pro_mask) dst_port (port_value) (port_mask)
-flags (flg_value) priority (prio_value) queue (queue_id) index (idx)
+port config - queues/descriptors
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
 
-The available information parameters are:
+Set number of queues/descriptors for rxq, txq, rxd and txd:
 
-*   port_id: the port which the 2-tuple filter assigned on.
+port config all (rxq|txq|rxd|txd) (value)
 
-*   pro_value: IP L4 protocol
+This is equivalent to the --rxq, --txq, --rxd and --txd command-line options.
 
-*   pro_mask: protocol participates in the match or not, 1 means participate
+port config - max-pkt-len
+~~~~~~~~~~~~~~~~~~~~~~~~~
 
-*   port_value: destination port in L4.
+Set the maximum packet length:
 
-*   port_mask: destination port participates in the match or not, 1 means participate.
+port config all max-pkt-len (value)
 
-*   flg_value: TCP control bits. The non-zero value is invalid, when the pro_value is not set to 0x06 (TCP).
+This is equivalent to the --max-pkt-len command-line option.
 
-*   prio_value: the priority of this filter.
+port config - CRC Strip
+~~~~~~~~~~~~~~~~~~~~~~~
 
-*   queue_id: The receive queue associated with this 2-tuple filter
+Set hardware CRC stripping on or off for all ports:
 
-*   index: the index of this 2-tuple filter
+port config all crc-strip (on|off)
 
-Example:
+CRC stripping is off by default.
 
-.. code-block:: console
+The on option is equivalent to the --crc-strip command-line option.
 
-    testpmd> add_2tuple_filter 0 protocol 0x06 1 dst_port 32 1 flags 0x02 priority 3 queue 3 index 0
+port config - RX Checksum
+~~~~~~~~~~~~~~~~~~~~~~~~~
 
-remove_2tuple_filter
-~~~~~~~~~~~~~~~~~~~~
+Set hardware RX checksum offload to on or off for all ports:
 
-Remove a 2-tuple filter
+port config all rx-cksum (on|off)
 
-remove_2tuple_filter (port_id) index (idx)
+Checksum offload is off by default.
 
-get_2tuple_filter
-~~~~~~~~~~~~~~~~~
+The on option is equivalent to the --enable-rx-cksum command-line option.
 
-Get and display a 2-tuple filter
+port config - VLAN
+~~~~~~~~~~~~~~~~~~
 
-get_2tuple_filter (port_id) index (idx)
+Set hardware VLAN on or off for all ports:
 
-Example:
+port config all hw-vlan (on|off)
 
-.. code-block:: console
+Hardware VLAN is on by default.
 
-    testpmd> get_2tuple_filter 0 index 0
+The off option is equivalent to the --disable-hw-vlan command-line option.
 
-    filter[0]:
-        Destination Port: 0x0020 mask: 1
-        protocol: 0x06 mask:1 tcp_flags: 0x02
-        priority: 3   queue: 3
+port config - Drop Packets
+~~~~~~~~~~~~~~~~~~~~~~~~~~
 
-add_5tuple_filter
-~~~~~~~~~~~~~~~~~
+Set packet drop for packets with no descriptors on or off for all ports:
 
-Add a 5-tuple filter,
-which consists of a 5-tuple (protocol, source and destination IP addresses, source and destination TCP/UDP/SCTP port)
-and routes packets into one of the receive queues.
+port config all drop-en (on|off)
 
-add_5tuple_filter (port_id) dst_ip (dst_address) src_ip (src_address) dst_port (dst_port_value) src_port (src_port_value)
-protocol (protocol_value) mask (mask_value) flags (flags_value) priority (prio_value) queue (queue_id) index (idx)
+Packet dropping for packets with no descriptors is off by default.
 
-The available information parameters are:
+The on option is equivalent to the --enable-drop-en command-line option.
 
-*   port_id: the port which the 5-tuple filter assigned on.
+port config - RSS
+~~~~~~~~~~~~~~~~~
 
-*   dst_address: destination IP address.
+Set the RSS (Receive Side Scaling) mode on or off:
 
-*   src_address: source IP address.
+port config all rss (ip|udp|none)
 
-*   dst_port_value: TCP/UDP destination port.
+RSS is on by default.
 
-*   src_port_value: TCP/UDP source port.
+The off option is equivalent to the --disable-rss command-line option.
 
-*   protocol_value: L4 protocol.
+port config - RSS Reta
+~~~~~~~~~~~~~~~~~~~~~~
 
-*   mask_value: participates in the match or not by bit for field above, 1b means participate
+Set the RSS (Receive Side Scaling) redirection table:
 
-*   flags_value: TCP control bits. The non-zero value is invalid, when the protocol_value is not set to 0x06 (TCP).
+port config all rss reta (hash,queue)[,(hash,queue)]
 
-*   prio_value: the priority of this filter.
+port config - DCB
+~~~~~~~~~~~~~~~~~
 
-*   queue_id: The receive queue associated with this 5-tuple filter.
+Set the DCB mode for an individual port:
 
-*   index: the index of this 5-tuple filter
+port config (port_id) dcb vt (on|off) (traffic_class) pfc (on|off)
 
-Example:
+The traffic class should be 4 or 8.
 
-.. code-block:: console
+port config - Burst
+~~~~~~~~~~~~~~~~~~~
 
-    testpmd> add_5tuple_filter 1 dst_ip 2.2.2.5 src_ip 2.2.2.4 dst_port 64 src_port 32 protocol 0x06 mask 0x1F flags 0x0 priority 3 queue 3 index 0
+Set the number of packets per burst:
 
-remove_5tuple_filter
-~~~~~~~~~~~~~~~~~~~~
+port config all burst (value)
 
-Remove a 5-tuple filter
+This is equivalent to the --burst command-line option.
 
-remove_5tuple_filter (port_id) index (idx)
+port config - Threshold
+~~~~~~~~~~~~~~~~~~~~~~~
 
-get_5tuple_filter
-~~~~~~~~~~~~~~~~~
+Set thresholds for TX/RX queues:
 
-Get and display a 5-tuple filter
+port config all (threshold) (value)
 
-get_5tuple_filter (port_id) index (idx)
+Where the threshold type can be:
 
-Example:
+*   txpt: Set the prefetch threshold register of the TX rings, 0 <= value <= 255.
 
-.. code-block:: console
+*   txht: Set the host threshold register of the TX rings, 0 <= value <= 255.
 
-    testpmd> get_5tuple_filter 1 index 0
+*   txwt: Set the write-back threshold register of the TX rings, 0 <= value <= 255.
 
-    filter[0]:
-        Destination IP: 0x02020205 mask: 1
-        Source IP: 0x02020204 mask: 1
-        Destination Port: 0x0040 mask: 1
-        Source Port: 0x0020 mask: 1
-        protocol: 0x06 mask: 1
-        priority: 3 flags: 0x00 queue: 3
+*   rxpt: Set the prefetch threshold register of the RX rings, 0 <= value <= 255.
 
-add_syn_filter
-~~~~~~~~~~~~~~
+*   rxht: Set the host threshold register of the RX rings, 0 <= value <= 255.
 
-Add SYN filter, which can forward TCP packets whose *SYN* flag is set into a separate queue.
+*   rxwt: Set the write-back threshold register of the RX rings, 0 <= value <= 255.
 
-add_syn_filter (port_id) priority (high|low) queue (queue_id)
+*   txfreet: Set the transmit free threshold of the TX rings, 0 <= value <= txd.
 
-The available information parameters are:
+*   rxfreet: Set the transmit free threshold of the RX rings, 0 <= value <= rxd.
 
-*   port_id: the port which the SYN filter assigned on.
+*   txrst: Set the transmit RS bit threshold of TX rings, 0 <= value <= txd.
+    These threshold options are also available from the command-line.
 
-*   high: this SYN filter has higher priority than other filters.
+Flow Director Functions
+-----------------------
 
-*   low: this SYN filter has lower priority than other filters.
+The Flow Director works in receive mode to identify specific flows or sets of flows and route them to specific queues.
 
-*   queue_id: The receive queue associated with this SYN filter
+Two types of filtering are supported which are referred to as Perfect Match and Signature filters:
 
-Example:
+*   Perfect match filters.
+    The hardware checks a match between the masked fields of the received packets and the programmed filters.
 
-.. code-block:: console
+*   Signature filters.
+    The hardware checks a match between a hash-based signature of the masked fields of the received packet.
 
-    testpmd> add_syn_filter 0 priority high queue 3,
+The Flow Director filters can match the following fields in a packet:
 
-remove_syn_filter
-~~~~~~~~~~~~~~~~~
+*   Source IP and destination IP addresses.
 
-Remove SYN filter
+*   Source port and destination port numbers (for UDP and TCP packets).
 
-remove_syn_filter (port_id)
+*   IPv4/IPv6 and UDP/ TCP/SCTP protocol match.
 
-get_syn_filter
-~~~~~~~~~~~~~~
+*   VLAN header.
 
-Get and display SYN filter
+*   Flexible 2-byte tuple match anywhere in the first 64 bytes of the packet.
 
-get_syn_filter (port_id)
+The Flow Director can also mask out parts of all of these fields so that filters are only applied to certain fields
+or parts of the fields.
+For example it is possible to mask out sub-nets of IP addresses or to ignore VLAN headers.
 
-Example:
+In the following sections, several common parameters are used in the Flow Director filters.
+These are explained below:
 
-.. code-block:: console
+*   src: A pair of source address values. The source IP, in IPv4 or IPv6 format, and the source port:
 
-    testpmd> get_syn_filter 0
+    src 192.168.0.1 1024
 
-    syn filter: on, priority: high, queue: 3
+    src 2001:DB8:85A3:0:0:8A2E:370:7000 1024
 
-add_flex_filter
-~~~~~~~~~~~~~~~
+*   dst: A pair of destination address values. The destination IP, in IPv4 or IPv6 format, and the destination port.
 
-Add a Flex filter,
-which recognizes any arbitrary pattern within the first 128 bytes of the packet
-and routes packets into one of the receive queues.
+*   flexbytes: A 2-byte tuple to be matched within the first 64 bytes of a packet.
 
-add_flex_filter (port_id) len (len_value) bytes (bytes_string) mask (mask_value)
-priority (prio_value) queue (queue_id) index (idx)
+The offset where the match occurs is set by the --pkt-filter-flexbytes-offset command-line parameter
+and is counted from the first byte of the destination Ethernet MAC address.
+The default offset is 0xC bytes, which is the "Type" word in the MAC header.
+Typically, the flexbyte value is set to 0x0800 to match the IPv4 MAC type or 0x86DD to match IPv6.
+These values change when a VLAN tag is added.
 
-The available information parameters are:
+*   vlan: The VLAN header to match in the packet.
 
-*   port_id: the port which the Flex filter assigned on.
+*   queue: The index of the RX queue to route matched packets to.
 
-*   len_value: filter length in byte, no greater than 128.
+*   soft: The 16-bit value in the MBUF flow director ID field for RX packets matching the filter.
 
-*   bytes_string: a sting in format of octal, means the value the flex filter need to match.
+add_signature_filter
+~~~~~~~~~~~~~~~~~~~~
 
-*   mask_value: a sting in format of octal, bit 1 means corresponding byte in DWORD participates in the match.
+Add a signature filter:
 
-*   prio_value: the priority of this filter.
+# Command is displayed on several lines for clarity.
 
-*   queue_id: The receive queue associated with this Flex filter.
+add_signature_filter (port_id) (ip|udp|tcp|sctp)
 
-*   index: the index of this Flex filter
+    src (src_ip_address) (src_port)
 
-Example:
+    dst (dst_ip_address) (dst_port)
 
-.. code-block:: console
+    flexbytes (flexbytes_values)
 
-   testpmd> add_flex_filter 0 len 16 bytes 0x00000000000000000000000008060000 mask 000C priority 3 queue 3 index 0
+    vlan (vlan_id) queue (queue_id)
 
-Assign a packet whose 13th and 14th bytes are 0x0806 to queue 3.
+upd_signature_filter
+~~~~~~~~~~~~~~~~~~~~
 
-remove_flex_filter
-~~~~~~~~~~~~~~~~~~
+Update a signature filter:
 
-Remove a Flex filter
+# Command is displayed on several lines for clarity.
 
-remove_flex_filter (port_id) index (idx)
+upd_signature_filter (port_id) (ip|udp|tcp|sctp)
 
-get_flex_filter
-~~~~~~~~~~~~~~~
+    src (src_ip_address) (src_port)
 
-Get and display a Flex filter
+    dst (dst_ip_address) (dst_port)
 
-get_flex_filter (port_id) index (idx)
+    flexbytes (flexbytes_values)
 
-Example:
+    vlan (vlan_id) queue (queue_id)
 
-.. code-block:: console
+rm_signature_filter
+~~~~~~~~~~~~~~~~~~~
 
-    testpmd> get_flex_filter 0 index 0
+Remove a signature filter:
 
-    filter[0]:
+# Command is displayed on several lines for clarity.
 
-        length: 16
+rm_signature_filter (port_id) (ip|udp|tcp|sctp)
 
-        dword[]: 0x00000000 00000000 00000000 08060000 00000000 00000000 00000000
-    00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
-    00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
-    00000000 00000000 00000000 00000000 00000000 00000000 00000000
+    src (src_ip_address) (src_port)
 
-        mask[]:
-    0b0000000000001100000000000000000000000000000000000000000000000000000000
-    0000000000000000000000000000000000000000000000000000000000
+    dst (dst_ip_address) (dst_port)
 
-        priority: 3   queue: 3
+    flexbytes (flexbytes_values)
 
-set link up
-~~~~~~~~~~~
+    vlan (vlan_id)
 
-Set link up for a port.
+add_perfect_filter
+~~~~~~~~~~~~~~~~~~
 
-set link-up port (port id)
+Add a perfect filter:
 
-set link down
-~~~~~~~~~~~~~
+# Command is displayed on several lines for clarity.
 
-Set link down for a port.
+add_perfect_filter (port_id) (ip|udp|tcp|sctp)
 
-set link-down port (port id)
+    src (src_ip_address) (src_port)
 
-Port Functions
---------------
+    dst (dst_ip_address) (dst_port)
 
-The following sections show functions for configuring ports.
+    flexbytes (flexbytes_values)
 
-.. note::
+    vlan (vlan_id) queue (queue_id) soft (soft_id)
 
-    Port configuration changes only become active when forwarding is started/restarted.
+upd_perfect_filter
+~~~~~~~~~~~~~~~~~~
 
-port start
-~~~~~~~~~~
+Update a perfect filter:
 
-Start all ports or a specific port:
+# Command is displayed on several lines for clarity.
 
-port start (port_id|all)
+upd_perfect_filter (port_id) (ip|udp|tcp|sctp)
 
-port stop
-~~~~~~~~~
+    src (src_ip_address) (src_port)
 
-Stop all ports or a specific port:
+    dst (dst_ip_address) (dst_port)
 
-port stop (port_id|all)
+    flexbytes (flexbytes_values)
 
-port close
-~~~~~~~~~~
+    vlan (vlan_id) queue (queue_id)
 
-Close all ports or a specific port:
+rm_perfect_filter
+~~~~~~~~~~~~~~~~~
 
-port close (port_id|all)
+Remove a perfect filter:
 
-port start/stop queue
-~~~~~~~~~~~~~~~~~~~~
+rm_perfect_filter (port_id) (ip|udp|tcp|sctp)
 
-Start/stop a rx/tx queue on a specific port:
+    src (src_ip_address) (src_port)
 
-port (port_id) (rxq|txq) (queue_id) (start|stop)
+    dst (dst_ip_address) (dst_port)
 
-Only take effect when port is started.
+    flexbytes (flexbytes_values)
 
-port config - speed
-~~~~~~~~~~~~~~~~~~~
+    vlan (vlan_id) soft (soft_id)
 
-Set the speed and duplex mode for all ports or a specific port:
+set_masks_filter
+~~~~~~~~~~~~~~~~
 
-port config (port_id|all) speed (10|100|1000|10000|auto) duplex (half|full|auto)
+Set IPv4 filter masks:
 
-port config - queues/descriptors
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+# Command is displayed on several lines for clarity.
 
-Set number of queues/descriptors for rxq, txq, rxd and txd:
+set_masks_filter (port_id) only_ip_flow (0|1)
 
-port config all (rxq|txq|rxd|txd) (value)
+    src_mask (ip_src_mask) (src_port_mask)
 
-This is equivalent to the --rxq, --txq, --rxd and --txd command-line options.
+    dst_mask (ip_dst_mask) (dst_port_mask)
 
-port config - max-pkt-len
-~~~~~~~~~~~~~~~~~~~~~~~~~
+    flexbytes (0|1) vlan_id (0|1) vlan_prio (0|1)
 
-Set the maximum packet length:
+set_ipv6_masks_filter
+~~~~~~~~~~~~~~~~~~~~~
 
-port config all max-pkt-len (value)
+Set IPv6 filter masks:
 
-This is equivalent to the --max-pkt-len command-line option.
+# Command is displayed on several lines for clarity.
 
-port config - CRC Strip
-~~~~~~~~~~~~~~~~~~~~~~~
+set_ipv6_masks_filter (port_id) only_ip_flow (0|1)
 
-Set hardware CRC stripping on or off for all ports:
+    src_mask (ip_src_mask) (src_port_mask)
 
-port config all crc-strip (on|off)
+    dst_mask (ip_dst_mask) (dst_port_mask)
 
-CRC stripping is off by default.
+    flexbytes (0|1) vlan_id (0|1) vlan_prio (0|1)
 
-The on option is equivalent to the --crc-strip command-line option.
+    compare_dst (0|1)
 
-port config - RX Checksum
-~~~~~~~~~~~~~~~~~~~~~~~~~
+Link Bonding Functions
+----------------------
 
-Set hardware RX checksum offload to on or off for all ports:
+The Link Bonding functions make it possible to dynamically create and
+manage link bonding devices from within testpmd interactive prompt.
 
-port config all rx-cksum (on|off)
+create bonded device
+~~~~~~~~~~~~~~~~~~~~
 
-Checksum offload is off by default.
+Create a new bonding device:
 
-The on option is equivalent to the --enable-rx-cksum command-line option.
+create bonded device (mode) (socket)
 
-port config - VLAN
-~~~~~~~~~~~~~~~~~~
+For example, to create a bonded device in mode 1 on socket 0.
 
-Set hardware VLAN on or off for all ports:
+.. code-block:: console
 
-port config all hw-vlan (on|off)
+    testpmd> create bonded 1 0
+    created new bonded device (port X)
 
-Hardware VLAN is on by default.
+add bonding slave
+~~~~~~~~~~~~~~~~~
 
-The off option is equivalent to the --disable-hw-vlan command-line option.
+Adds Ethernet device to a Link Bonding device:
 
-port config - Drop Packets
-~~~~~~~~~~~~~~~~~~~~~~~~~~
+add bonding slave (slave id) (port id)
 
-Set packet drop for packets with no descriptors on or off for all ports:
+For example, to add Ethernet device (port 6) to a Link Bonding device (port 10).
 
-port config all drop-en (on|off)
+.. code-block:: console
 
-Packet dropping for packets with no descriptors is off by default.
+    testpmd> add bonding slave 6 10
 
-The on option is equivalent to the --enable-drop-en command-line option.
 
-port config - RSS
-~~~~~~~~~~~~~~~~~
+remove bonding slave
+~~~~~~~~~~~~~~~~~~~~
 
-Set the RSS (Receive Side Scaling) mode on or off:
+Removes an Ethernet slave device from a Link Bonding device:
 
-port config all rss (ip|udp|none)
+remove bonding slave (slave id) (port id)
 
-RSS is on by default.
+For example, to remove Ethernet slave device (port 6) to a Link Bonding device (port 10).
 
-The off option is equivalent to the --disable-rss command-line option.
+.. code-block:: console
 
-port config - RSS Reta
-~~~~~~~~~~~~~~~~~~~~~~
+    testpmd> remove bonding slave 6 10
 
-Set the RSS (Receive Side Scaling) redirection table:
+set bonding mode
+~~~~~~~~~~~~~~~~
 
-port config all rss reta (hash,queue)[,(hash,queue)]
+Set the Link Bonding mode of a Link Bonding device:
 
-port config - DCB
-~~~~~~~~~~~~~~~~~
+set bonding mode (value) (port id)
 
-Set the DCB mode for an individual port:
+For example, to set the bonding mode of a Link Bonding device (port 10) to broadcast (mode 3).
 
-port config (port_id) dcb vt (on|off) (traffic_class) pfc (on|off)
+.. code-block:: console
 
-The traffic class should be 4 or 8.
+    testpmd> set bonding mode 3 10
 
-port config - Burst
+set bonding primary
 ~~~~~~~~~~~~~~~~~~~
 
-Set the number of packets per burst:
-
-port config all burst (value)
-
-This is equivalent to the --burst command-line option.
+Set an Ethernet slave device as the primary device on a Link Bonding device:
 
-port config - Threshold
-~~~~~~~~~~~~~~~~~~~~~~~
+set bonding primary (slave id) (port id)
 
-Set thresholds for TX/RX queues:
+For example, to set the Ethernet slave device (port 6) as the primary port of a Link Bonding device (port 10).
 
-port config all (threshold) (value)
+.. code-block:: console
 
-Where the threshold type can be:
+    testpmd> set bonding primary 6 10
 
-*   txpt: Set the prefetch threshold register of the TX rings, 0 <= value <= 255.
+set bonding mac
+~~~~~~~~~~~~~~~
 
-*   txht: Set the host threshold register of the TX rings, 0 <= value <= 255.
+Set the MAC address of a Link Bonding device:
 
-*   txwt: Set the write-back threshold register of the TX rings, 0 <= value <= 255.
+set bonding mac (port id) (mac)
 
-*   rxpt: Set the prefetch threshold register of the RX rings, 0 <= value <= 255.
+For example, to set the MAC address of a Link Bonding device (port 10) to 00:00:00:00:00:01
 
-*   rxht: Set the host threshold register of the RX rings, 0 <= value <= 255.
+.. code-block:: console
 
-*   rxwt: Set the write-back threshold register of the RX rings, 0 <= value <= 255.
+    testpmd> set bonding mac 10 00:00:00:00:00:01
 
-*   txfreet: Set the transmit free threshold of the TX rings, 0 <= value <= txd.
+set bonding xmit_balance_policy
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
 
-*   rxfreet: Set the transmit free threshold of the RX rings, 0 <= value <= rxd.
+Set the transmission policy for a Link Bonding device when it is in Balance XOR mode:
 
-*   txrst: Set the transmit RS bit threshold of TX rings, 0 <= value <= txd.
-    These threshold options are also available from the command-line.
+set bonding xmit_balance_policy (port_id) (l2|l23|l34)
 
-Flow Director Functions
------------------------
+For example, set a Link Bonding device (port 10) to use a balance policy of layer 3+4 (IP addresses & UDP ports )
 
-The Flow Director works in receive mode to identify specific flows or sets of flows and route them to specific queues.
+.. code-block:: console
 
-Two types of filtering are supported which are referred to as Perfect Match and Signature filters:
+    testpmd> set bonding xmit_balance_policy 10 l34
 
-*   Perfect match filters.
-    The hardware checks a match between the masked fields of the received packets and the programmed filters.
+show bonding config
+~~~~~~~~~~~~~~~~~~~
 
-*   Signature filters.
-    The hardware checks a match between a hash-based signature of the masked fields of the received packet.
+Show the current configuration of a Link Bonding device:
 
-The Flow Director filters can match the following fields in a packet:
+show bonding config (port id)
 
-*   Source IP and destination IP addresses.
+For example,
+to show the configuration a Link Bonding device (port 9) with 3 slave devices (1, 3, 4)
+in balance mode with a transmission policy of layer 2+3.
 
-*   Source port and destination port numbers (for UDP and TCP packets).
+.. code-block:: console
 
-*   IPv4/IPv6 and UDP/ TCP/SCTP protocol match.
+    testpmd> show bonding config 9
+        Bonding mode: 2
+        Balance Xmit Policy: BALANCE_XMIT_POLICY_LAYER23
+        Slaves (3): [1 3 4]
+        Active Slaves (3): [1 3 4]
+        Primary: [3]
 
-*   VLAN header.
+Register Functions
+------------------
 
-*   Flexible 2-byte tuple match anywhere in the first 64 bytes of the packet.
+The Register functions can be used to read from and write to registers on the network card referenced by a port number.
+This is mainly useful for debugging purposes.
+Reference should be made to the appropriate datasheet for the network card for details on the register addresses
+and fields that can be accessed.
 
-The Flow Director can also mask out parts of all of these fields so that filters are only applied to certain fields
-or parts of the fields.
-For example it is possible to mask out sub-nets of IP addresses or to ignore VLAN headers.
+read reg
+~~~~~~~~
 
-In the following sections, several common parameters are used in the Flow Director filters.
-These are explained below:
+Display the value of a port register:
 
-*   src: A pair of source address values. The source IP, in IPv4 or IPv6 format, and the source port:
+read reg (port_id) (address)
 
-    src 192.168.0.1 1024
+For example, to examine the Flow Director control register (FDIRCTL, 0x0000EE000) on an Intel® 82599 10 GbE Controller:
 
-    src 2001:DB8:85A3:0:0:8A2E:370:7000 1024
+.. code-block:: console
 
-*   dst: A pair of destination address values. The destination IP, in IPv4 or IPv6 format, and the destination port.
+    testpmd> read reg 0 0xEE00
+    port 0 PCI register at offset 0xEE00: 0x4A060029 (1241907241)
 
-*   flexbytes: A 2-byte tuple to be matched within the first 64 bytes of a packet.
+read regfield
+~~~~~~~~~~~~~
 
-The offset where the match occurs is set by the --pkt-filter-flexbytes-offset command-line parameter
-and is counted from the first byte of the destination Ethernet MAC address.
-The default offset is 0xC bytes, which is the "Type" word in the MAC header.
-Typically, the flexbyte value is set to 0x0800 to match the IPv4 MAC type or 0x86DD to match IPv6.
-These values change when a VLAN tag is added.
+Display a port register bit field:
 
-*   vlan: The VLAN header to match in the packet.
+read regfield (port_id) (address) (bit_x) (bit_y)
 
-*   queue: The index of the RX queue to route matched packets to.
+For example, reading the lowest two bits from the register in the example above:
 
-*   soft: The 16-bit value in the MBUF flow director ID field for RX packets matching the filter.
+.. code-block:: console
 
-add_signature_filter
-~~~~~~~~~~~~~~~~~~~~
+    testpmd> read regfield 0 0xEE00 0 1
+    port 0 PCI register at offset 0xEE00: bits[0, 1]=0x1 (1)
 
-Add a signature filter:
+read regbit
+~~~~~~~~~~~
 
-# Command is displayed on several lines for clarity.
+Display a single port register bit:
 
-add_signature_filter (port_id) (ip|udp|tcp|sctp)
+read regbit (port_id) (address) (bit_x)
 
-    src (src_ip_address) (src_port)
+For example, reading the lowest bit from the register in the example above:
 
-    dst (dst_ip_address) (dst_port)
+.. code-block:: console
 
-    flexbytes (flexbytes_values)
+    testpmd> read regbit 0 0xEE00 0
+    port 0 PCI register at offset 0xEE00: bit 0=1
 
-    vlan (vlan_id) queue (queue_id)
+write reg
+~~~~~~~~~
 
-upd_signature_filter
-~~~~~~~~~~~~~~~~~~~~
+Set the value of a port register:
 
-Update a signature filter:
+write reg (port_id) (address) (value)
 
-# Command is displayed on several lines for clarity.
+For example, to clear a register:
 
-upd_signature_filter (port_id) (ip|udp|tcp|sctp)
+.. code-block:: console
 
-    src (src_ip_address) (src_port)
+    testpmd> write reg 0 0xEE00 0x0
+    port 0 PCI register at offset 0xEE00: 0x00000000 (0)
 
-    dst (dst_ip_address) (dst_port)
+write regfield
+~~~~~~~~~~~~~~
 
-    flexbytes (flexbytes_values)
+Set bit field of a port register:
 
-    vlan (vlan_id) queue (queue_id)
+write regfield (port_id) (address) (bit_x) (bit_y) (value)
 
-rm_signature_filter
-~~~~~~~~~~~~~~~~~~~
+For example, writing to the register cleared in the example above:
 
-Remove a signature filter:
+.. code-block:: console
 
-# Command is displayed on several lines for clarity.
+    testpmd> write regfield 0 0xEE00 0 1 2
+    port 0 PCI register at offset 0xEE00: 0x00000002 (2)
 
-rm_signature_filter (port_id) (ip|udp|tcp|sctp)
+write regbit
+~~~~~~~~~~~~
 
-    src (src_ip_address) (src_port)
+Set single bit value of a port register:
 
-    dst (dst_ip_address) (dst_port)
+write regbit (port_id) (address) (bit_x) (value)
 
-    flexbytes (flexbytes_values)
+For example, to set the high bit in the register from the example above:
 
-    vlan (vlan_id)
+.. code-block:: console
 
-add_perfect_filter
-~~~~~~~~~~~~~~~~~~
+    testpmd> write regbit 0 0xEE00 31 1
+    port 0 PCI register at offset 0xEE00: 0x8000000A (2147483658)
 
-Add a perfect filter:
+Filter Functions
+-----------------------
 
-# Command is displayed on several lines for clarity.
+This section details the available filter functions that are available.
 
-add_perfect_filter (port_id) (ip|udp|tcp|sctp)
+add_ethertype_filter
+~~~~~~~~~~~~~~~~~~~~
 
-    src (src_ip_address) (src_port)
+Add a L2 Ethertype filter, which identify packets by their L2 Ethertype mainly assign them to a receive queue.
 
-    dst (dst_ip_address) (dst_port)
+add_ethertype_filter (port_id) ethertype (eth_value) priority (enable|disable) (pri_value) queue (queue_id) index (idx)
 
-    flexbytes (flexbytes_values)
+The available information parameters are:
 
-    vlan (vlan_id) queue (queue_id) soft (soft_id)
+*   port_id:  the port which the Ethertype filter assigned on.
 
-upd_perfect_filter
-~~~~~~~~~~~~~~~~~~
+*   eth_value: the EtherType value want to match,
+    for example 0x0806 for ARP packet. 0x0800 (IPv4) and 0x86DD (IPv6) are invalid.
 
-Update a perfect filter:
+*   enable: user priority participates in the match.
 
-# Command is displayed on several lines for clarity.
+*   disable: user priority doesn't participate in the match.
 
-upd_perfect_filter (port_id) (ip|udp|tcp|sctp)
+*   pri_value: user priority value that want to match.
 
-    src (src_ip_address) (src_port)
+*   queue_id : The receive queue associated with this EtherType filter
 
-    dst (dst_ip_address) (dst_port)
+*   index: the index of this EtherType filter
 
-    flexbytes (flexbytes_values)
+Example:
 
-    vlan (vlan_id) queue (queue_id)
+.. code-block:: console
 
-rm_perfect_filter
-~~~~~~~~~~~~~~~~~
+    testpmd> add_ethertype_filter 0 ethertype 0x0806 priority disable 0 queue 3 index 0
+    Assign ARP packet to receive queue 3
 
-Remove a perfect filter:
+remove_ethertype_filter
+~~~~~~~~~~~~~~~~~~~~~~~
 
-rm_perfect_filter (port_id) (ip|udp|tcp|sctp)
+Remove a L2 Ethertype filter
 
-    src (src_ip_address) (src_port)
+remove_ethertype_filter (port_id) index (idx)
 
-    dst (dst_ip_address) (dst_port)
+get_ethertype_filter
+~~~~~~~~~~~~~~~~~~~~
 
-    flexbytes (flexbytes_values)
+Get and display a L2 Ethertype filter
 
-    vlan (vlan_id) soft (soft_id)
+get_ethertype_filter (port_id) index (idx)
 
-set_masks_filter
-~~~~~~~~~~~~~~~~
+Example:
 
-Set IPv4 filter masks:
+.. code-block:: console
 
-# Command is displayed on several lines for clarity.
+    testpmd> get_ethertype_filter 0 index 0
 
-set_masks_filter (port_id) only_ip_flow (0|1)
+    filter[0]:
+        ethertype: 0x0806
+        priority: disable, 0
+        queue: 3
 
-    src_mask (ip_src_mask) (src_port_mask)
+add_2tuple_filter
+~~~~~~~~~~~~~~~~~
 
-    dst_mask (ip_dst_mask) (dst_port_mask)
+Add a 2-tuple filter,
+which identify packets by specific protocol and destination TCP/UDP port
+and forwards packets into one of the receive queues.
 
-    flexbytes (0|1) vlan_id (0|1) vlan_prio (0|1)
+add_2tuple_filter (port_id) protocol (pro_value) (pro_mask) dst_port (port_value) (port_mask)
+flags (flg_value) priority (prio_value) queue (queue_id) index (idx)
 
-set_ipv6_masks_filter
-~~~~~~~~~~~~~~~~~~~~~
+The available information parameters are:
 
-Set IPv6 filter masks:
+*   port_id: the port which the 2-tuple filter assigned on.
 
-# Command is displayed on several lines for clarity.
+*   pro_value: IP L4 protocol
 
-set_ipv6_masks_filter (port_id) only_ip_flow (0|1)
+*   pro_mask: protocol participates in the match or not, 1 means participate
 
-    src_mask (ip_src_mask) (src_port_mask)
+*   port_value: destination port in L4.
 
-    dst_mask (ip_dst_mask) (dst_port_mask)
+*   port_mask: destination port participates in the match or not, 1 means participate.
 
-    flexbytes (0|1) vlan_id (0|1) vlan_prio (0|1)
+*   flg_value: TCP control bits. The non-zero value is invalid, when the pro_value is not set to 0x06 (TCP).
 
-    compare_dst (0|1)
+*   prio_value: the priority of this filter.
 
-Link Bonding Functions
-----------------------
+*   queue_id: The receive queue associated with this 2-tuple filter
 
-The Link Bonding functions make it possible to dynamically create and
-manage link bonding devices from within testpmd interactive prompt.
+*   index: the index of this 2-tuple filter
 
-create bonded device
-~~~~~~~~~~~~~~~~~~~~
+Example:
 
-Create a new bonding device:
+.. code-block:: console
 
-create bonded device (mode) (socket)
+    testpmd> add_2tuple_filter 0 protocol 0x06 1 dst_port 32 1 flags 0x02 priority 3 queue 3 index 0
 
-For example, to create a bonded device in mode 1 on socket 0.
+remove_2tuple_filter
+~~~~~~~~~~~~~~~~~~~~
 
-.. code-block:: console
+Remove a 2-tuple filter
 
-    testpmd> create bonded 1 0
-    created new bonded device (port X)
+remove_2tuple_filter (port_id) index (idx)
 
-add bonding slave
+get_2tuple_filter
 ~~~~~~~~~~~~~~~~~
 
-Adds Ethernet device to a Link Bonding device:
+Get and display a 2-tuple filter
 
-add bonding slave (slave id) (port id)
+get_2tuple_filter (port_id) index (idx)
 
-For example, to add Ethernet device (port 6) to a Link Bonding device (port 10).
+Example:
 
 .. code-block:: console
 
-    testpmd> add bonding slave 6 10
+    testpmd> get_2tuple_filter 0 index 0
 
+    filter[0]:
+        Destination Port: 0x0020 mask: 1
+        protocol: 0x06 mask:1 tcp_flags: 0x02
+        priority: 3   queue: 3
 
-remove bonding slave
-~~~~~~~~~~~~~~~~~~~~
+add_5tuple_filter
+~~~~~~~~~~~~~~~~~
 
-Removes an Ethernet slave device from a Link Bonding device:
+Add a 5-tuple filter,
+which consists of a 5-tuple (protocol, source and destination IP addresses, source and destination TCP/UDP/SCTP port)
+and routes packets into one of the receive queues.
 
-remove bonding slave (slave id) (port id)
+add_5tuple_filter (port_id) dst_ip (dst_address) src_ip (src_address) dst_port (dst_port_value) src_port (src_port_value)
+protocol (protocol_value) mask (mask_value) flags (flags_value) priority (prio_value) queue (queue_id) index (idx)
 
-For example, to remove Ethernet slave device (port 6) to a Link Bonding device (port 10).
+The available information parameters are:
 
-.. code-block:: console
+*   port_id: the port which the 5-tuple filter assigned on.
 
-    testpmd> remove bonding slave 6 10
+*   dst_address: destination IP address.
 
-set bonding mode
-~~~~~~~~~~~~~~~~
+*   src_address: source IP address.
 
-Set the Link Bonding mode of a Link Bonding device:
+*   dst_port_value: TCP/UDP destination port.
 
-set bonding mode (value) (port id)
+*   src_port_value: TCP/UDP source port.
 
-For example, to set the bonding mode of a Link Bonding device (port 10) to broadcast (mode 3).
+*   protocol_value: L4 protocol.
 
-.. code-block:: console
+*   mask_value: participates in the match or not by bit for field above, 1b means participate
 
-    testpmd> set bonding mode 3 10
+*   flags_value: TCP control bits. The non-zero value is invalid, when the protocol_value is not set to 0x06 (TCP).
 
-set bonding primary
-~~~~~~~~~~~~~~~~~~~
+*   prio_value: the priority of this filter.
 
-Set an Ethernet slave device as the primary device on a Link Bonding device:
+*   queue_id: The receive queue associated with this 5-tuple filter.
 
-set bonding primary (slave id) (port id)
+*   index: the index of this 5-tuple filter
 
-For example, to set the Ethernet slave device (port 6) as the primary port of a Link Bonding device (port 10).
+Example:
 
 .. code-block:: console
 
-    testpmd> set bonding primary 6 10
+    testpmd> add_5tuple_filter 1 dst_ip 2.2.2.5 src_ip 2.2.2.4 dst_port 64 src_port 32 protocol 0x06 mask 0x1F flags 0x0 priority 3 queue 3 index 0
 
-set bonding mac
-~~~~~~~~~~~~~~~
+remove_5tuple_filter
+~~~~~~~~~~~~~~~~~~~~
 
-Set the MAC address of a Link Bonding device:
+Remove a 5-tuple filter
 
-set bonding mac (port id) (mac)
+remove_5tuple_filter (port_id) index (idx)
 
-For example, to set the MAC address of a Link Bonding device (port 10) to 00:00:00:00:00:01
+get_5tuple_filter
+~~~~~~~~~~~~~~~~~
+
+Get and display a 5-tuple filter
+
+get_5tuple_filter (port_id) index (idx)
+
+Example:
 
 .. code-block:: console
 
-    testpmd> set bonding mac 10 00:00:00:00:00:01
+    testpmd> get_5tuple_filter 1 index 0
 
-set bonding xmit_balance_policy
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+    filter[0]:
+        Destination IP: 0x02020205 mask: 1
+        Source IP: 0x02020204 mask: 1
+        Destination Port: 0x0040 mask: 1
+        Source Port: 0x0020 mask: 1
+        protocol: 0x06 mask: 1
+        priority: 3 flags: 0x00 queue: 3
 
-Set the transmission policy for a Link Bonding device when it is in Balance XOR mode:
+add_syn_filter
+~~~~~~~~~~~~~~
 
-set bonding xmit_balance_policy (port_id) (l2|l23|l34)
+Add SYN filter, which can forward TCP packets whose *SYN* flag is set into a separate queue.
 
-For example, set a Link Bonding device (port 10) to use a balance policy of layer 3+4 (IP addresses & UDP ports )
+add_syn_filter (port_id) priority (high|low) queue (queue_id)
 
-.. code-block:: console
+The available information parameters are:
 
-    testpmd> set bonding xmit_balance_policy 10 l34
+*   port_id: the port which the SYN filter assigned on.
 
-show bonding config
-~~~~~~~~~~~~~~~~~~~
+*   high: this SYN filter has higher priority than other filters.
 
-Show the current configuration of a Link Bonding device:
+*   low: this SYN filter has lower priority than other filters.
 
-show bonding config (port id)
+*   queue_id: The receive queue associated with this SYN filter
 
-For example,
-to show the configuration a Link Bonding device (port 9) with 3 slave devices (1, 3, 4)
-in balance mode with a transmission policy of layer 2+3.
+Example:
 
 .. code-block:: console
 
-    testpmd> show bonding config 9
-        Bonding mode: 2
-        Balance Xmit Policy: BALANCE_XMIT_POLICY_LAYER23
-        Slaves (3): [1 3 4]
-        Active Slaves (3): [1 3 4]
-        Primary: [3]
+    testpmd> add_syn_filter 0 priority high queue 3,
 
-Register Functions
-------------------
+remove_syn_filter
+~~~~~~~~~~~~~~~~~
 
-The Register functions can be used to read from and write to registers on the network card referenced by a port number.
-This is mainly useful for debugging purposes.
-Reference should be made to the appropriate datasheet for the network card for details on the register addresses
-and fields that can be accessed.
+Remove SYN filter
 
-read reg
-~~~~~~~~
+remove_syn_filter (port_id)
 
-Display the value of a port register:
+get_syn_filter
+~~~~~~~~~~~~~~
 
-read reg (port_id) (address)
+Get and display SYN filter
 
-For example, to examine the Flow Director control register (FDIRCTL, 0x0000EE000) on an Intel® 82599 10 GbE Controller:
+get_syn_filter (port_id)
+
+Example:
 
 .. code-block:: console
 
-    testpmd> read reg 0 0xEE00
-    port 0 PCI register at offset 0xEE00: 0x4A060029 (1241907241)
+    testpmd> get_syn_filter 0
 
-read regfield
-~~~~~~~~~~~~~
+    syn filter: on, priority: high, queue: 3
 
-Display a port register bit field:
+add_flex_filter
+~~~~~~~~~~~~~~~
 
-read regfield (port_id) (address) (bit_x) (bit_y)
+Add a Flex filter,
+which recognizes any arbitrary pattern within the first 128 bytes of the packet
+and routes packets into one of the receive queues.
 
-For example, reading the lowest two bits from the register in the example above:
+add_flex_filter (port_id) len (len_value) bytes (bytes_string) mask (mask_value)
+priority (prio_value) queue (queue_id) index (idx)
 
-.. code-block:: console
+The available information parameters are:
 
-    testpmd> read regfield 0 0xEE00 0 1
-    port 0 PCI register at offset 0xEE00: bits[0, 1]=0x1 (1)
+*   port_id: the port which the Flex filter assigned on.
 
-read regbit
-~~~~~~~~~~~
+*   len_value: filter length in byte, no greater than 128.
 
-Display a single port register bit:
+*   bytes_string: a sting in format of octal, means the value the flex filter need to match.
 
-read regbit (port_id) (address) (bit_x)
+*   mask_value: a sting in format of octal, bit 1 means corresponding byte in DWORD participates in the match.
 
-For example, reading the lowest bit from the register in the example above:
+*   prio_value: the priority of this filter.
 
-.. code-block:: console
+*   queue_id: The receive queue associated with this Flex filter.
 
-    testpmd> read regbit 0 0xEE00 0
-    port 0 PCI register at offset 0xEE00: bit 0=1
+*   index: the index of this Flex filter
 
-write reg
-~~~~~~~~~
+Example:
 
-Set the value of a port register:
+.. code-block:: console
 
-write reg (port_id) (address) (value)
+   testpmd> add_flex_filter 0 len 16 bytes 0x00000000000000000000000008060000 mask 000C priority 3 queue 3 index 0
 
-For example, to clear a register:
+Assign a packet whose 13th and 14th bytes are 0x0806 to queue 3.
 
-.. code-block:: console
+remove_flex_filter
+~~~~~~~~~~~~~~~~~~
 
-    testpmd> write reg 0 0xEE00 0x0
-    port 0 PCI register at offset 0xEE00: 0x00000000 (0)
+Remove a Flex filter
 
-write regfield
-~~~~~~~~~~~~~~
+remove_flex_filter (port_id) index (idx)
 
-Set bit field of a port register:
+get_flex_filter
+~~~~~~~~~~~~~~~
 
-write regfield (port_id) (address) (bit_x) (bit_y) (value)
+Get and display a Flex filter
 
-For example, writing to the register cleared in the example above:
+get_flex_filter (port_id) index (idx)
 
-.. code-block:: console
+Example:
 
-    testpmd> write regfield 0 0xEE00 0 1 2
-    port 0 PCI register at offset 0xEE00: 0x00000002 (2)
+.. code-block:: console
 
-write regbit
-~~~~~~~~~~~~
+    testpmd> get_flex_filter 0 index 0
 
-Set single bit value of a port register:
+    filter[0]:
 
-write regbit (port_id) (address) (bit_x) (value)
+        length: 16
 
-For example, to set the high bit in the register from the example above:
+        dword[]: 0x00000000 00000000 00000000 08060000 00000000 00000000 00000000
+    00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
+    00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
+    00000000 00000000 00000000 00000000 00000000 00000000 00000000
 
-.. code-block:: console
+        mask[]:
+    0b0000000000001100000000000000000000000000000000000000000000000000000000
+    0000000000000000000000000000000000000000000000000000000000
 
-    testpmd> write regbit 0 0xEE00 31 1
-    port 0 PCI register at offset 0xEE00: 0x8000000A (2147483658)
+        priority: 3   queue: 3
