[v2,1/2] net/octeontx2: add support to enable switch type

  From: Kiran Kumar K <kirankumark@marvell.com>

Adding support to configure specific switch types like high2 and dsa
on a port. When this switch type is configured, it is expected that
all the traffic on that port should be of specific type only.

Signed-off-by: Kiran Kumar K <kirankumark@marvell.com>
---
V2 Changes:
* Fixed checkpatch issue

 doc/guides/nics/octeontx2.rst               | 12 +++++++++
 drivers/common/octeontx2/otx2_mbox.h        | 19 ++++++++++++-
 drivers/net/octeontx2/otx2_ethdev.c         | 30 +++++++++++++++++++++
 drivers/net/octeontx2/otx2_ethdev_devargs.c | 22 ++++++++++++++-
 drivers/net/octeontx2/otx2_flow.h           |  1 +
 5 files changed, 82 insertions(+), 2 deletions(-)

--
2.17.1
  

On Wed, Oct 23, 2019 at 8:56 PM <kirankumark@marvell.com> wrote:
>
> From: Kiran Kumar K <kirankumark@marvell.com>
>
> Adding support to configure specific switch types like high2 and dsa
> on a port. When this switch type is configured, it is expected that
> all the traffic on that port should be of specific type only.
>
> Signed-off-by: Kiran Kumar K <kirankumark@marvell.com>
> ---
> V2 Changes:
> * Fixed checkpatch issue

Series Acked-by: Jerin Jacob <jerinj@marvell.com>

Series applied to dpdk-next-net-mrvl/master. Thanks.


>
>  doc/guides/nics/octeontx2.rst               | 12 +++++++++
>  drivers/common/octeontx2/otx2_mbox.h        | 19 ++++++++++++-
>  drivers/net/octeontx2/otx2_ethdev.c         | 30 +++++++++++++++++++++
>  drivers/net/octeontx2/otx2_ethdev_devargs.c | 22 ++++++++++++++-
>  drivers/net/octeontx2/otx2_flow.h           |  1 +
>  5 files changed, 82 insertions(+), 2 deletions(-)
>
> diff --git a/doc/guides/nics/octeontx2.rst b/doc/guides/nics/octeontx2.rst
> index fc8a130fb..adf7c7131 100644
> --- a/doc/guides/nics/octeontx2.rst
> +++ b/doc/guides/nics/octeontx2.rst
> @@ -170,6 +170,18 @@ Runtime Config Options
>     With the above configuration, each send queue's decscriptor buffer count is
>     limited to a maximum of 64 buffers.
>
> +- ``switch header enable`` (default ``none``)
> +
> +   A port can be configured to a specific switch header type by using
> +   ``switch_header`` ``devargs`` parameter.
> +
> +   For example::
> +
> +      -w 0002:02:00.0,switch_header="higig2"
> +
> +   With the above configuration, higig2 will be enabled on that port and the
> +   traffic on this port should be higig2 traffic only. Supported switch header
> +   types are "higig2" and "dsa".
>
>  .. note::
>
> diff --git a/drivers/common/octeontx2/otx2_mbox.h b/drivers/common/octeontx2/otx2_mbox.h
> index 445b03e26..c2a9e9fe6 100644
> --- a/drivers/common/octeontx2/otx2_mbox.h
> +++ b/drivers/common/octeontx2/otx2_mbox.h
> @@ -89,7 +89,7 @@ struct mbox_msghdr {
>  #define OTX2_MBOX_RSP_SIG (0xbeef)
>         /* Signature, for validating corrupted msgs */
>         uint16_t __otx2_io sig;
> -#define OTX2_MBOX_VERSION (0x0002)
> +#define OTX2_MBOX_VERSION (0x0003)
>         /* Version of msg's structure for this ID */
>         uint16_t __otx2_io ver;
>         /* Offset of next msg within mailbox region */
> @@ -236,6 +236,9 @@ M(NPC_DELETE_FLOW,    0x600e, npc_delete_flow,                      \
>  M(NPC_MCAM_READ_ENTRY,   0x600f, npc_mcam_read_entry,                  \
>                                   npc_mcam_read_entry_req,              \
>                                   npc_mcam_read_entry_rsp)              \
> +M(NPC_SET_PKIND,          0x6010, npc_set_pkind,                        \
> +                                 npc_set_pkind,                        \
> +                                 msg_rsp)                              \
>  /* NIX mbox IDs (range 0x8000 - 0xFFFF) */                             \
>  M(NIX_LF_ALLOC,                0x8000, nix_lf_alloc, nix_lf_alloc_req,         \
>                                 nix_lf_alloc_rsp)                       \
> @@ -329,6 +332,20 @@ struct ready_msg_rsp {
>         uint16_t __otx2_io rclk_freq; /* RCLK frequency */
>  };
>
> +/* Struct to set pkind */
> +struct npc_set_pkind {
> +       struct mbox_msghdr hdr;
> +#define OTX2_PRIV_FLAGS_DEFAULT  BIT_ULL(0)
> +#define OTX2_PRIV_FLAGS_EDSA     BIT_ULL(1)
> +#define OTX2_PRIV_FLAGS_HIGIG    BIT_ULL(2)
> +#define OTX2_PRIV_FLAGS_CUSTOM   BIT_ULL(63)
> +       uint64_t __otx2_io mode;
> +#define PKIND_TX               BIT_ULL(0)
> +#define PKIND_RX               BIT_ULL(1)
> +       uint8_t __otx2_io dir;
> +       uint8_t __otx2_io pkind; /* valid only in case custom flag */
> +};
> +
>  /* Structure for requesting resource provisioning.
>   * 'modify' flag to be used when either requesting more
>   * or detach partial of a certain resource type.
> diff --git a/drivers/net/octeontx2/otx2_ethdev.c b/drivers/net/octeontx2/otx2_ethdev.c
> index 62291c698..dfa8cd205 100644
> --- a/drivers/net/octeontx2/otx2_ethdev.c
> +++ b/drivers/net/octeontx2/otx2_ethdev.c
> @@ -90,6 +90,30 @@ nix_lf_alloc(struct otx2_eth_dev *dev, uint32_t nb_rxq, uint32_t nb_txq)
>         return 0;
>  }
>
> +static int
> +nix_lf_switch_header_type_enable(struct otx2_eth_dev *dev)
> +{
> +       struct otx2_mbox *mbox = dev->mbox;
> +       struct npc_set_pkind *req;
> +       struct msg_resp *rsp;
> +       int rc;
> +
> +       if (dev->npc_flow.switch_header_type == 0)
> +               return 0;
> +
> +       /* Notify AF about higig2 config */
> +       req = otx2_mbox_alloc_msg_npc_set_pkind(mbox);
> +       req->mode = dev->npc_flow.switch_header_type;
> +       req->dir = PKIND_RX;
> +       rc = otx2_mbox_process_msg(mbox, (void *)&rsp);
> +       if (rc)
> +               return rc;
> +       req = otx2_mbox_alloc_msg_npc_set_pkind(mbox);
> +       req->mode = dev->npc_flow.switch_header_type;
> +       req->dir = PKIND_TX;
> +       return otx2_mbox_process_msg(mbox, (void *)&rsp);
> +}
> +
>  static int
>  nix_lf_free(struct otx2_eth_dev *dev)
>  {
> @@ -1612,6 +1636,12 @@ otx2_nix_configure(struct rte_eth_dev *eth_dev)
>                 goto fail_offloads;
>         }
>
> +       rc = nix_lf_switch_header_type_enable(dev);
> +       if (rc) {
> +               otx2_err("Failed to enable switch type nix_lf rc=%d", rc);
> +               goto free_nix_lf;
> +       }
> +
>         rc = nix_setup_lso_formats(dev);
>         if (rc) {
>                 otx2_err("failed to setup nix lso format fields, rc=%d", rc);
> diff --git a/drivers/net/octeontx2/otx2_ethdev_devargs.c b/drivers/net/octeontx2/otx2_ethdev_devargs.c
> index 7dc6e92be..ca9a5ffb8 100644
> --- a/drivers/net/octeontx2/otx2_ethdev_devargs.c
> +++ b/drivers/net/octeontx2/otx2_ethdev_devargs.c
> @@ -104,12 +104,27 @@ parse_sqb_count(const char *key, const char *value, void *extra_args)
>         return 0;
>  }
>
> +static int
> +parse_switch_header_type(const char *key, const char *value, void *extra_args)
> +{
> +       RTE_SET_USED(key);
> +
> +       if (strcmp(value, "higig2") == 0)
> +               *(uint16_t *)extra_args = OTX2_PRIV_FLAGS_HIGIG;
> +
> +       if (strcmp(value, "dsa") == 0)
> +               *(uint16_t *)extra_args = OTX2_PRIV_FLAGS_EDSA;
> +
> +       return 0;
> +}
> +
>  #define OTX2_RSS_RETA_SIZE "reta_size"
>  #define OTX2_PTYPE_DISABLE "ptype_disable"
>  #define OTX2_SCL_ENABLE "scalar_enable"
>  #define OTX2_MAX_SQB_COUNT "max_sqb_count"
>  #define OTX2_FLOW_PREALLOC_SIZE "flow_prealloc_size"
>  #define OTX2_FLOW_MAX_PRIORITY "flow_max_priority"
> +#define OTX2_SWITCH_HEADER_TYPE "switch_header"
>
>  int
>  otx2_ethdev_parse_devargs(struct rte_devargs *devargs, struct otx2_eth_dev *dev)
> @@ -118,6 +133,7 @@ otx2_ethdev_parse_devargs(struct rte_devargs *devargs, struct otx2_eth_dev *dev)
>         uint16_t rss_size = NIX_RSS_RETA_SIZE;
>         uint16_t sqb_count = NIX_MAX_SQB;
>         uint16_t flow_prealloc_size = 8;
> +       uint16_t switch_header_type = 0;
>         uint16_t flow_max_priority = 3;
>         uint16_t scalar_enable = 0;
>         struct rte_kvargs *kvlist;
> @@ -141,6 +157,8 @@ otx2_ethdev_parse_devargs(struct rte_devargs *devargs, struct otx2_eth_dev *dev)
>                            &parse_flow_prealloc_size, &flow_prealloc_size);
>         rte_kvargs_process(kvlist, OTX2_FLOW_MAX_PRIORITY,
>                            &parse_flow_max_priority, &flow_max_priority);
> +       rte_kvargs_process(kvlist, OTX2_SWITCH_HEADER_TYPE,
> +                          &parse_switch_header_type, &switch_header_type);
>         rte_kvargs_free(kvlist);
>
>  null_devargs:
> @@ -150,6 +168,7 @@ otx2_ethdev_parse_devargs(struct rte_devargs *devargs, struct otx2_eth_dev *dev)
>         dev->rss_info.rss_size = rss_size;
>         dev->npc_flow.flow_prealloc_size = flow_prealloc_size;
>         dev->npc_flow.flow_max_priority = flow_max_priority;
> +       dev->npc_flow.switch_header_type = switch_header_type;
>         return 0;
>
>  exit:
> @@ -162,4 +181,5 @@ RTE_PMD_REGISTER_PARAM_STRING(net_octeontx2,
>                               OTX2_SCL_ENABLE "=1"
>                               OTX2_MAX_SQB_COUNT "=<8-512>"
>                               OTX2_FLOW_PREALLOC_SIZE "=<1-32>"
> -                             OTX2_FLOW_MAX_PRIORITY "=<1-32>");
> +                             OTX2_FLOW_MAX_PRIORITY "=<1-32>"
> +                             OTX2_SWITCH_HEADER_TYPE "=<higig2|dsa>");
> diff --git a/drivers/net/octeontx2/otx2_flow.h b/drivers/net/octeontx2/otx2_flow.h
> index ab068b088..6bfd5afde 100644
> --- a/drivers/net/octeontx2/otx2_flow.h
> +++ b/drivers/net/octeontx2/otx2_flow.h
> @@ -190,6 +190,7 @@ struct otx2_npc_flow_info {
>         uint16_t channel; /*rx channel */
>         uint16_t flow_prealloc_size;
>         uint16_t flow_max_priority;
> +       uint16_t switch_header_type;
>  };
>
>  struct otx2_parse_state {
> --
> 2.17.1
>