diff --git a/test_plans/vm2vm_virtio_net_perf_dsa_test_plan.rst b/test_plans/vm2vm_virtio_net_perf_dsa_test_plan.rst
new file mode 100644
index 00000000..70bb371a
--- /dev/null
+++ b/test_plans/vm2vm_virtio_net_perf_dsa_test_plan.rst
@@ -0,0 +1,1342 @@
+.. SPDX-License-Identifier: BSD-3-Clause
+   Copyright(c) 2022 Intel Corporation
+
+======================================================
+VM2VM vhost-user/virtio-net with DSA driver test plan
+======================================================
+
+Description
+===========
+
+Vhost asynchronous data path leverages DMA devices to offload memory copies from the CPU and it is implemented in an asynchronous way.
+In addition, vhost supports M:N mapping between vrings and DMA virtual channels. Specifically, one vring can use multiple different DMA
+channels and one DMA channel can be shared by multiple vrings at the same time.Vhost enqueue and dequeue operation with CBDMA channels is supported
+in both split and packed ring.
+
+This document provides the test plan for testing the following features when Vhost-user using asynchronous data path with
+DSA driver (kernel IDXD driver and DPDK vfio-pci driver) in VM2VM virtio-net topology.
+1. Check Vhost tx offload function by verifing the TSO/cksum in the TCP/IP stack with vm2vm split ring and packed ring 
+vhost-user/virtio-net mergeable path.
+2.Check the payload of large packet (larger than 1MB) is valid after forwarding packets with vm2vm split ring
+and packed ring vhost-user/virtio-net mergeable and non-mergeable path.
+3. Multi-queues number dynamic change in vm2vm vhost-user/virtio-net with split ring and packed ring.
+
+IOMMU impact:
+If iommu off, idxd can work with iova=pa
+If iommu on, kernel dsa driver only can work with iova=va by program IOMMU, can't use iova=pa(fwd not work due to pkts payload wrong).
+
+Note:
+1.For packed virtqueue virtio-net test, need qemu version > 4.2.0 and VM kernel version > 5.1, and packed ring multi-queues not support reconnect in qemu yet.
+2.For split virtqueue virtio-net with multi-queues server mode test, better to use qemu version >= 5.2.0, dut to qemu(v4.2.0~v5.1.0) exist split ring multi-queues reconnection issue.
+3.When DMA devices are bound to vfio driver, VA mode is the default and recommended. For PA mode, page by page mapping may
+exceed IOMMU's max capability, better to use 1G guest hugepage.
+4.DPDK local patch that about vhost pmd is needed when testing Vhost asynchronous data path with testpmd.
+
+Prerequisites
+=============
+
+Topology
+--------
+	Test flow: Virtio-net <-> Vhost-user <-> Testpmd <-> Vhost-user <-> Virtio-net
+
+Software
+--------
+	iperf
+	qemu: https://download.qemu.org/qemu-6.2.0.tar.xz
+
+General set up
+--------------
+1. Compile DPDK::
+
+	# CC=gcc meson --werror -Denable_kmods=True -Dlibdir=lib -Dexamples=all --default-library=static <dpdk build dir>
+	# ninja -C <dpdk build dir> -j 110
+	For example,
+	CC=gcc meson --werror -Denable_kmods=True -Dlibdir=lib -Dexamples=all --default-library=static x86_64-native-linuxapp-gcc
+	ninja -C x86_64-native-linuxapp-gcc -j 110
+
+2. Get the PCI device ID and DSA device ID of DUT, for example, 0000:4f:00.1 is PCI device ID, 0000:6a:01.0 - 0000:f6:01.0 are DSA device IDs::
+
+	<dpdk dir># ./usertools/dpdk-devbind.py -s
+
+	Network devices using kernel driver
+	===================================
+	0000:4f:00.1 'Ethernet Controller E810-C for QSFP 1592' drv=ice unused=vfio-pci
+
+	DMA devices using kernel driver
+	===============================
+	0000:6a:01.0 'Device 0b25' drv=idxd unused=vfio-pci
+	0000:6f:01.0 'Device 0b25' drv=idxd unused=vfio-pci
+	0000:74:01.0 'Device 0b25' drv=idxd unused=vfio-pci
+	0000:79:01.0 'Device 0b25' drv=idxd unused=vfio-pci
+	0000:e7:01.0 'Device 0b25' drv=idxd unused=vfio-pci
+	0000:ec:01.0 'Device 0b25' drv=idxd unused=vfio-pci
+	0000:f1:01.0 'Device 0b25' drv=idxd unused=vfio-pci
+	0000:f6:01.0 'Device 0b25' drv=idxd unused=vfio-pci
+
+Test case
+=========
+
+Common steps
+------------
+1. Bind DSA devices to DPDK vfio-pci driver::
+
+	<dpdk dir># ./usertools/dpdk-devbind.py -b vfio-pci <DUT port DSA device id>
+
+	For example, bind 2 DMA devices to vfio-pci driver:
+	<dpdk dir># ./usertools/dpdk-devbind.py -b vfio-pci 0000:e7:01.0 0000:ec:01.0
+
+.. note::
+
+	One DPDK DSA device can create 8 WQ at most. Below is an example, where DPDK DSA device will create one and
+	eight WQ for DSA deivce 0000:e7:01.0 and 0000:ec:01.0. The value of “max_queues” is 1~8:
+	<dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 4 -n 4 -a 0000:e7:01.0,max_queues=1 -- -i
+	<dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 4 -n 4 -a 0000:ec:01.0,max_queues=8 -- -i
+
+2. Bind DSA devices to kernel idxd driver, and configure Work Queue (WQ)::
+
+	<dpdk dir># ./usertools/dpdk-devbind.py -b idxd <numDevices * 2>
+	<dpdk dir># ./drivers/dma/idxd/dpdk_idxd_cfg.py -q <numWq>
+
+.. note::
+
+	Better to reset WQ when need operate DSA devices that bound to idxd drvier: 
+	<dpdk dir># ./drivers/dma/idxd/dpdk_idxd_cfg.py --reset <numDevices>
+	You can check it by 'ls /dev/dsa'
+	numDevices: number of devices, where 0<=numDevices<=7, corresponding to 0000:6a:01.0 - 0000:f6:01.0
+	numWq: Number of workqueues per DSA endpoint, where 1<=numWq<=8
+
+	For example, bind 2 DMA devices to idxd driver and configure WQ:
+
+	<dpdk dir># ./usertools/dpdk-devbind.py -b idxd 6a:01.0 6f:01.0
+	<dpdk dir># ./drivers/dma/idxd/dpdk_idxd_cfg.py -q 1 0
+	<dpdk dir># ./drivers/dma/idxd/dpdk_idxd_cfg.py -q 4 1
+	Check WQ by 'ls /dev/dsa' and can find "wq0.0 wq1.0 wq1.1 wq1.2 wq1.3"
+
+Test Case 1: VM2VM vhost-user/virtio-net split ring test TSO with dsa dpdk driver
+-----------------------------------------------------------------------------------
+This case test the function of Vhost tx offload in the topology of vhost-user/virtio-net split ring mergeable path 
+by verifing the TSO/cksum in the TCP/IP stack when vhost uses the asynchronous enqueue and dequeue operations with dsa dpdk driver.
+
+1. Bind 1 dsa device to vfio-pci like common step 1::
+
+	<dpdk dir># ./usertools/dpdk-devbind.py -b vfio-pci e7:01.0
+
+2. Launch the Vhost testpmd by below commands::
+
+	<dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 1-5 -n 4 --file-prefix=vhost -a 0000:e7:01.0,max_queues=2 \
+	--vdev 'net_vhost0,iface=vhost-net0,queues=1,tso=1,dmas=[txq0;rxq0]' \
+	--vdev 'net_vhost1,iface=vhost-net1,queues=1,tso=1,dmas=[txq0;rxq0]' \
+	--iova=va -- -i --nb-cores=2 --txd=1024 --rxd=1024 --rxq=1 --txq=1 --lcore-dma=[lcore2@0000:e7:01.0-q0,lcore3@0000:e7:01.0-q1]
+	testpmd>start
+
+3. Launch VM1 and VM2 with split ring mergeable path and tso on::
+
+	<dpdk dir># taskset -c 7 /usr/local/qemu-7.0.0/bin/qemu-system-x86_64 -name vm1 -enable-kvm -cpu host -smp 8 -m 4096 \
+	-object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge,share=on \
+	-numa node,memdev=mem -mem-prealloc -drive file=/home/xingguang/osimg/ubuntu20-04.img  \
+	-chardev socket,path=/tmp/vm1_qga0.sock,server,nowait,id=vm1_qga0 -device virtio-serial \
+	-device virtserialport,chardev=vm1_qga0,name=org.qemu.guest_agent.2 -daemonize \
+	-monitor unix:/tmp/vm1_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
+	-netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6002-:22 \
+	-chardev socket,id=char0,path=./vhost-net0 \
+	-netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce \
+	-device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:01,disable-modern=false,mrg_rxbuf=off,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on -vnc :10
+
+	<dpdk dir># taskset -c 8 /usr/local/qemu-7.0.0/bin/qemu-system-x86_64 -name vm2 -enable-kvm -cpu host -smp 8 -m 4096 \
+	-object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge,share=on \
+	-numa node,memdev=mem -mem-prealloc -drive file=/home/xingguang/osimg/ubuntu20-04-2.img  \
+	-chardev socket,path=/tmp/vm2_qga0.sock,server,nowait,id=vm2_qga0 -device virtio-serial \
+	-device virtserialport,chardev=vm2_qga0,name=org.qemu.guest_agent.2 -daemonize \
+	-monitor unix:/tmp/vm2_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
+	-netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6003-:22 \
+	-chardev socket,id=char0,path=./vhost-net1 \
+	-netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce \
+	-device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:02,disable-modern=false,mrg_rxbuf=off,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on -vnc :12
+
+4. On VM1, set virtio device IP and run arp protocal::
+
+	<VM1># ifconfig ens5 1.1.1.2
+	<VM1># arp -s 1.1.1.8 52:54:00:00:00:02
+
+5. On VM2, set virtio device IP and run arp protocal::
+
+	<VM2># ifconfig ens5 1.1.1.8
+	<VM2># arp -s 1.1.1.2 52:54:00:00:00:01
+
+6. Check the iperf performance between two VMs by below commands::
+
+	<VM1># iperf -s -i 1
+	<VM2># iperf -c 1.1.1.2 -i 1 -t 60
+
+7. Check that 2VMs can receive and send big packets to each other through vhost log. Port 0 should have tx packets above 1519, Port 1 should have rx packets above 1519::
+
+	testpmd>show port xstats all
+
+Test Case 2: VM2VM vhost-user/virtio-net split ring mergeable path 8 queues test with large packet payload with dsa dpdk driver
+---------------------------------------------------------------------------------------------------------------------------------
+This case uses iperf and scp to test the payload of large packet (larger than 1MB) is valid after packets forwarding in 
+vm2vm vhost-user/virtio-net split ring mergeable path when vhost uses the asynchronous enqueue and dequeue operations with dsa dpdk driver.
+The dynamic change of multi-queues number, iova as VA and PA mode also test.
+
+1. Bind 4 dsa device to vfio-pci like common step 1::
+
+	<dpdk dir># ./usertools/dpdk-devbind.py -b vfio-pci f1:01.0 f6:01.0
+
+2. Launch the Vhost testpmd by below commands::
+
+	<dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 1-5 -n 4 --file-prefix=vhost -a 0000:f1:01.0,max_queues=4 \
+	--vdev 'net_vhost0,iface=vhost-net0,queues=8,client=1,tso=1,dmas=[txq0;txq1;txq2;txq3;txq4;txq5;txq6;txq7;rxq0;rxq1;rxq2;rxq3;rxq4;rxq5;rxq6;rxq7]' \
+	--vdev 'net_vhost1,iface=vhost-net1,queues=8,client=1,tso=1,dmas=[txq0;txq1;txq2;txq3;txq4;txq5;txq6;txq7;rxq0;rxq1;rxq2;rxq3;rxq4;rxq5;rxq6;rxq7]' \
+	--iova=va -- -i --nb-cores=4 --txd=1024 --rxd=1024 --rxq=8 --txq=8 --lcore-dma=[lcore2@0000:f1:01.0-q0,lcore3@0000:f1:01.0-q1,lcore4@0000:f1:01.0-q2,lcore5@0000:f1:01.0-q3]
+	testpmd>start
+
+3. Launch VM1 and VM2 using qemu 7.0.0::
+
+	<dpdk dir># taskset -c 7 /usr/local/qemu-7.0.0/bin/qemu-system-x86_64 -name vm1 -enable-kvm -cpu host -smp 8 -m 4096 \
+	-object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge,share=on \
+	-numa node,memdev=mem -mem-prealloc -drive file=/home/xingguang/osimg/ubuntu20-04.img  \
+	-chardev socket,path=/tmp/vm2_qga0.sock,server,nowait,id=vm2_qga0 -device virtio-serial \
+	-device virtserialport,chardev=vm2_qga0,name=org.qemu.guest_agent.2 -daemonize \
+	-monitor unix:/tmp/vm2_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
+	-netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6002-:22 \
+	-chardev socket,id=char0,path=./vhost-net0,server \
+	-netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce,queues=8 \
+	-device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:01,disable-modern=false,mrg_rxbuf=on,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on -vnc :10
+
+	<dpdk dir># taskset -c 8 /usr/local/qemu-7.0.0/bin/qemu-system-x86_64 -name vm2 -enable-kvm -cpu host -smp 8 -m 4096 \
+	-object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge,share=on \
+	-numa node,memdev=mem -mem-prealloc -drive file=/home/xingguang/osimg/ubuntu20-04-2.img  \
+	-chardev socket,path=/tmp/vm2_qga0.sock,server,nowait,id=vm2_qga0 -device virtio-serial \
+	-device virtserialport,chardev=vm2_qga0,name=org.qemu.guest_agent.2 -daemonize \
+	-monitor unix:/tmp/vm2_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
+	-netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6003-:22 \
+	-chardev socket,id=char0,path=./vhost-net1,server \
+	-netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce,queues=8 \
+	-device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:02,disable-modern=false,mrg_rxbuf=on,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on -vnc :12
+
+4. On VM1, set virtio device IP and run arp protocal::
+
+	<VM1># ethtool -L ens5 combined 8
+	<VM1># ifconfig ens5 1.1.1.2
+	<VM1># arp -s 1.1.1.8 52:54:00:00:00:02
+
+5. On VM2, set virtio device IP and run arp protocal::
+
+	<VM2># ethtool -L ens5 combined 8
+	<VM2># ifconfig ens5 1.1.1.8
+	<VM2># arp -s 1.1.1.2 52:54:00:00:00:01
+
+6. Scp 1MB file form VM1 to VM2::
+
+	<VM1># scp <file> root@1.1.1.8:/
+
+7. Check the iperf performance between two VMs by below commands::
+
+	<VM1># iperf -s -i 1
+	<VM2># iperf -c 1.1.1.2 -i 1 -t 60
+
+8. Quit and relaunch vhost w/ diff dsa channels::
+
+	<dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 1-5 -n 4 --file-prefix=vhost -a 0000:f1:01.0,max_queues=4  -a 0000:f6:01.0,max_queues=4 \
+	--vdev 'net_vhost0,iface=vhost-net0,client=1,queues=8,tso=1,dmas=[txq0;txq1;txq2;txq3;txq4;txq5;rxq2;rxq3;rxq4;rxq5;rxq6;rxq7]' \
+	--vdev 'net_vhost1,iface=vhost-net1,client=1,queues=8,tso=1,dmas=[txq0;txq1;txq2;txq3;txq4;txq5;rxq2;rxq3;rxq4;rxq5;rxq6;rxq7]' \
+	--iova=va -- -i --nb-cores=4 --txd=1024 --rxd=1024 --rxq=8 --txq=8 \
+	--lcore-dma=[lcore2@0000:f1:01.0-q0,lcore3@0000:f1:01.0-q0,lcore3@0000:f1:01.0-q1,lcore3@0000:f1:01.0-q2,lcore4@0000:f1:01.0-q3,lcore4@0000:f6:01.0-q0,lcore4@0000:f6:01.0-q1,lcore4@0000:f6:01.0-q2,lcore5@0000:f6:01.0-q0,lcore5@0000:f6:01.0-q1,lcore5@0000:f6:01.0-q2,lcore5@0000:f6:01.0-q3]
+	testpmd>start
+
+9. Rerun step 6-7.
+
+10. Quit and relaunch vhost w/ iova=pa::
+
+	<dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 1-5 -n 4 --file-prefix=vhost -a 0000:f1:01.0,max_queues=4 \
+	--vdev 'net_vhost0,iface=vhost-net0,client=1,queues=8,tso=1,dmas=[txq0;txq1;txq2;txq3;txq4;txq5;rxq2;rxq3;rxq4;rxq5;rxq6;rxq7]' \
+	--vdev 'net_vhost1,iface=vhost-net1,client=1,queues=8,tso=1,dmas=[txq0;txq1;txq2;txq3;txq4;txq5;rxq2;rxq3;rxq4;rxq5;rxq6;rxq7]' \
+	--iova=pa -- -i --nb-cores=4 --txd=1024 --rxd=1024 --rxq=8 --txq=8 --lcore-dma=[lcore2@0000:f1:01.0-q0,lcore3@0000:f1:01.0-q1,lcore4@0000:f1:01.0-q2,lcore5@0000:f1:01.0-q3]
+	testpmd>start
+
+11. Rerun step 6-7.
+
+12. Quit vhost ports and relaunch vhost ports w/o dsa channels::
+
+	<dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 1-5 -n 4 --file-prefix=vhost --no-pci --vdev 'net_vhost0,iface=vhost-net0,client=1,tso=1,queues=8' \
+	--vdev 'net_vhost1,iface=vhost-net1,client=1,tso=1,queues=8'  -- -i --nb-cores=4 --txd=1024 --rxd=1024 --rxq=4 --txq=4
+	testpmd>start
+
+13. On VM1, set virtio device::
+
+	<VM1># ethtool -L ens5 combined 4
+
+14. On VM2, set virtio device::
+
+	<VM2># ethtool -L ens5 combined 4
+
+15. Rerun step 6-7.
+
+16. Quit vhost ports and relaunch vhost ports with 1 queues::
+
+	<dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 1-5 -n 4 --file-prefix=vhost --no-pci --vdev 'net_vhost0,iface=vhost-net0,client=1,tso=1,queues=4' \
+	--vdev 'net_vhost1,iface=vhost-net1,client=1,tso=1,queues=4'  -- -i --nb-cores=4 --txd=1024 --rxd=1024 --rxq=1 --txq=1
+	testpmd>start
+
+17. On VM1, set virtio device::
+
+	<VM1># ethtool -L ens5 combined 1
+
+18. On VM2, set virtio device::
+
+	<VM2># ethtool -L ens5 combined 1
+
+19. Rerun step 6-7.
+
+Test Case 3: VM2VM vhost-user/virtio-net split ring non-mergeable path 8 queues test with large packet payload with dsa dpdk driver
+------------------------------------------------------------------------------------------------------------------------------------
+This case uses iperf and scp to test the payload of large packet (larger than 1MB) is valid after packets forwarding in
+vm2vm vhost-user/virtio-net split ring non-mergeable path when vhost uses the asynchronous enqueue and dequeue operations with dsa dpdk driver.
+The dynamic change of multi-queues number also test.
+
+1. Bind 2 dsa device to vfio-pci like common step 1::
+
+	<dpdk dir># ./usertools/dpdk-devbind.py -b vfio-pci e7:01.0 ec:01.0
+
+2. Launch the Vhost sample by below commands::
+
+	<dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 1-5 -n 4 --file-prefix=vhost -a 0000:f1:01.0,max_queues=4 \
+	--vdev 'net_vhost0,iface=vhost-net0,client=1,queues=8,tso=1,dmas=[txq0;txq1;txq2;txq3;txq4;txq5;txq6;txq7;rxq0;rxq1;rxq2;rxq3;rxq4;rxq5;rxq6;rxq7]' \
+	--vdev 'net_vhost1,iface=vhost-net1,client=1,queues=8,tso=1,dmas=[txq0;txq1;txq2;txq3;txq4;txq5;txq6;txq7;rxq0;rxq1;rxq2;rxq3;rxq4;rxq5;rxq6;rxq7]' \
+	--iova=va -- -i --nb-cores=4 --txd=1024 --rxd=1024 --rxq=8 --txq=8 --lcore-dma=[lcore2@0000:f1:01.0-q0,lcore3@0000:f1:01.0-q1,lcore4@0000:f1:01.0-q2,lcore5@0000:f1:01.0-q3]
+	testpmd>start
+
+3. Launch VM1 and VM2::
+
+	<dpdk dir># taskset -c 7 /usr/local/qemu-7.0.0/bin/qemu-system-x86_64 -name vm1 -enable-kvm -cpu host -smp 8 -m 4096 \
+	-object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge,share=on \
+	-numa node,memdev=mem -mem-prealloc -drive file=/home/xingguang/osimg/ubuntu20-04.img  \
+	-chardev socket,path=/tmp/vm1_qga0.sock,server,nowait,id=vm1_qga0 -device virtio-serial \
+	-device virtserialport,chardev=vm1_qga0,name=org.qemu.guest_agent.2 -daemonize \
+	-monitor unix:/tmp/vm1_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
+	-netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6002-:22 \
+	-chardev socket,id=char0,path=./vhost-net0,server \
+	-netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce,queues=8 \
+	-device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:01,disable-modern=false,mrg_rxbuf=off,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on -vnc :10
+
+	<dpdk dir># taskset -c 8 /usr/local/qemu-7.0.0/bin/qemu-system-x86_64 -name vm2 -enable-kvm -cpu host -smp 8 -m 4096 \
+	-object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge,share=on \
+	-numa node,memdev=mem -mem-prealloc -drive file=/home/xingguang/osimg/ubuntu20-04-2.img  \
+	-chardev socket,path=/tmp/vm2_qga0.sock,server,nowait,id=vm2_qga0 -device virtio-serial \
+	-device virtserialport,chardev=vm2_qga0,name=org.qemu.guest_agent.2 -daemonize \
+	-monitor unix:/tmp/vm2_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
+	-netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6003-:22 \
+	-chardev socket,id=char0,path=./vhost-net1,server \
+	-netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce,queues=8 \
+	-device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:02,disable-modern=false,mrg_rxbuf=off,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on -vnc :12
+
+4. On VM1, set virtio device IP and run arp protocal::
+
+	<VM1># ethtool -L ens5 combined 8
+	<VM1># ifconfig ens5 1.1.1.2
+	<VM1># arp -s 1.1.1.8 52:54:00:00:00:02
+
+5. On VM2, set virtio device IP and run arp protocal::
+
+	<VM2># ethtool -L ens5 combined 8
+	<VM2># ifconfig ens5 1.1.1.8
+	<VM2># arp -s 1.1.1.2 52:54:00:00:00:01
+
+6. Scp 1MB file form VM1 to VM2::
+
+	<VM1># scp <file> root@1.1.1.8:/
+
+7. Check the iperf performance between two VMs by below commands::
+
+	<VM1># iperf -s -i 1
+	<VM2># iperf -c 1.1.1.2 -i 1 -t 60
+
+8. Quit vhost ports and relaunch vhost ports w/o dsa channels::
+
+	<dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 1-5 -n 4 --file-prefix=vhost --no-pci --vdev 'net_vhost0,iface=vhost-net0,client=1,tso=1,queues=8' \
+	--vdev 'net_vhost1,iface=vhost-net1,client=1,tso=1,queues=8'  -- -i --nb-cores=4 --txd=1024 --rxd=1024 --rxq=8 --txq=8
+	testpmd>start
+
+9. Rerun step 6-7.
+
+10. Quit vhost ports and relaunch vhost ports with 1 queues::
+
+	<dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 1-5 -n 4 --file-prefix=vhost --no-pci --vdev 'net_vhost0,iface=vhost-net0,client=1,tso=1,queues=8' \
+	--vdev 'net_vhost1,iface=vhost-net1,client=1,tso=1,queues=8'  -- -i --nb-cores=4 --txd=1024 --rxd=1024 --rxq=1 --txq=1
+	testpmd>start
+
+11. On VM1, set virtio device::
+
+	<VM1># ethtool -L ens5 combined 1
+
+12. On VM2, set virtio device::
+
+	<VM2># ethtool -L ens5 combined 1
+
+13. Rerun step 6-7.
+
+Test Case 4: VM2VM vhost-user/virtio-net packed ring test TSO with dsa dpdk driver
+-----------------------------------------------------------------------------------
+This case test the function of Vhost tx offload in the topology of vhost-user/virtio-net packed ring mergeable path 
+by verifing the TSO/cksum in the TCP/IP stack when vhost uses the asynchronous enqueue and dequeue operations with dsa dpdk driver.
+
+1. Bind 2 dsa device to vfio-pci like common step 1::
+
+	<dpdk dir># ./usertools/dpdk-devbind.py -b vfio-pci f1:01.0 f6:01.0
+
+2. Launch the Vhost sample by below commands::
+
+	<dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 2-4 -n 4 --file-prefix=vhost -a 0000:f1:01.0,max_queues=2 \
+	--vdev 'net_vhost0,iface=vhost-net0,queues=1,tso=1,dmas=[txq0;rxq0]' \
+	--vdev 'net_vhost1,iface=vhost-net1,queues=1,tso=1,dmas=[txq0;rxq0]' \
+	--iova=va -- -i --nb-cores=2 --txd=1024 --rxd=1024 --lcore-dma=[lcore3@0000:f1:01.0-q0,lcore4@0000:f1:01.0-q1]
+	testpmd>start
+
+3. Launch VM1 and VM2 with qemu::
+
+	<dpdk dir># taskset -c 7 /usr/local/qemu-7.0.0/bin/qemu-system-x86_64 -name vm1 -enable-kvm -cpu host -smp 1 -m 4096 \
+	-object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge,share=on \
+	-numa node,memdev=mem -mem-prealloc -drive file=/home/xingguang/osimg/ubuntu20-04.img  \
+	-chardev socket,path=/tmp/vm1_qga0.sock,server,nowait,id=vm1_qga0 -device virtio-serial \
+	-device virtserialport,chardev=vm1_qga0,name=org.qemu.guest_agent.2 -daemonize \
+	-monitor unix:/tmp/vm1_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
+	-netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6002-:22 \
+	-chardev socket,id=char0,path=./vhost-net0 \
+	-netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce \
+	-device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:01,disable-modern=false,mrg_rxbuf=on,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,packed=on -vnc :10
+
+	<dpdk dir># taskset -c 8 /usr/local/qemu-7.0.0/bin/qemu-system-x86_64 -name vm2 -enable-kvm -cpu host -smp 1 -m 4096 \
+	-object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge,share=on \
+	-numa node,memdev=mem -mem-prealloc -drive file=/home/xingguang/osimg/ubuntu20-04-2.img  \
+	-chardev socket,path=/tmp/vm2_qga0.sock,server,nowait,id=vm2_qga0 -device virtio-serial \
+	-device virtserialport,chardev=vm2_qga0,name=org.qemu.guest_agent.2 -daemonize \
+	-monitor unix:/tmp/vm2_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
+	-netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6003-:22 \
+	-chardev socket,id=char0,path=./vhost-net1 \
+	-netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce \
+	-device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:02,disable-modern=false,mrg_rxbuf=on,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,packed=on -vnc :12
+
+4. On VM1, set virtio device IP and run arp protocal::
+
+	<VM1># ifconfig ens5 1.1.1.2
+	<VM1># arp -s 1.1.1.8 52:54:00:00:00:02
+
+5. On VM2, set virtio device IP and run arp protocal::
+
+	<VM2># ifconfig ens5 1.1.1.8
+	<VM2># arp -s 1.1.1.2 52:54:00:00:00:01
+
+6. Check the iperf performance between two VMs by below commands::
+
+	<VM1># iperf -s -i 1
+	<VM2># iperf -c 1.1.1.2 -i 1 -t 60
+
+7. Check that 2VMs can receive and send big packets to each other through vhost log. Port 0 should have tx packets above 1519, Port 1 should have rx packets above 1519::
+
+	testpmd>show port xstats all
+
+Test Case 5: VM2VM vhost-user/virtio-net packed ring mergeable path 8 queues test with large packet payload with dsa dpdk driver
+---------------------------------------------------------------------------------------------------------------------------------
+This case uses iperf and scp to test the payload of large packet (larger than 1MB) is valid after packets forwarding in 
+vm2vm vhost-user/virtio-net packed ring mergeable path when vhost uses the asynchronous enqueue and dequeue operations with dsa dpdk driver.
+The dynamic change of multi-queues number also test.
+
+1. Bind 2 dsa device to vfio-pci like common step 1::
+
+	<dpdk dir># ./usertools/dpdk-devbind.py -b vfio-pci f1:01.0 f6:01.0
+
+2. Launch the Vhost sample by below commands::
+
+	<dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 1-5 -n 4 --file-prefix=vhost -a 0000:f1:01.0,max_queues=4 -a 0000:f6:01.0,max_queues=4 \
+	--vdev 'net_vhost0,iface=vhost-net0,queues=8,tso=1,dmas=[txq0;txq1;txq2;txq3;txq4;txq5;txq6;txq7;rxq0;rxq1;rxq2;rxq3;rxq4;rxq5;rxq6;rxq7]' \
+	--vdev 'net_vhost1,iface=vhost-net1,queues=8,tso=1,dmas=[txq0;txq1;txq2;txq3;txq4;txq5;txq6;txq7;rxq0;rxq1;rxq2;rxq3;rxq4;rxq5;rxq6;rxq7]' \
+	--iova=va -- -i --nb-cores=4 --txd=1024 --rxd=1024 --rxq=8 --txq=8 \
+	--lcore-dma=[lcore2@0000:f1:01.0-q0,lcore2@0000:f1:01.0-q1,lcore3@0000:f1:01.0-q2,lcore3@0000:f1:01.0-q3,lcore4@0000:f6:01.0-q0,lcore4@0000:f6:01.0-q1,lcore5@0000:f6:01.0-q2,lcore5@0000:f6:01.0-q3]
+	testpmd>start
+
+3. Launch VM1 and VM2 with qemu::
+
+	<dpdk dir># taskset -c 7 /usr/local/qemu-7.0.0/bin/qemu-system-x86_64 -name vm1 -enable-kvm -cpu host -smp 8 -m 4096 \
+	-object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge,share=on \
+	-numa node,memdev=mem -mem-prealloc -drive file=/home/xingguang/osimg/ubuntu20-04.img  \
+	-chardev socket,path=/tmp/vm1_qga0.sock,server,nowait,id=vm1_qga0 -device virtio-serial \
+	-device virtserialport,chardev=vm1_qga0,name=org.qemu.guest_agent.2 -daemonize \
+	-monitor unix:/tmp/vm1_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
+	-netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6002-:22 \
+	-chardev socket,id=char0,path=./vhost-net0 \
+	-netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce,queues=8 \
+	-device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:01,disable-modern=false,mrg_rxbuf=on,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on,packed=on -vnc :10
+
+	<dpdk dir># taskset -c 8 /usr/local/qemu-7.0.0/bin/qemu-system-x86_64 -name vm2 -enable-kvm -cpu host -smp 8 -m 4096 \
+	-object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge,share=on \
+	-numa node,memdev=mem -mem-prealloc -drive file=/home/xingguang/osimg/ubuntu20-04-2.img  \
+	-chardev socket,path=/tmp/vm2_qga0.sock,server,nowait,id=vm2_qga0 -device virtio-serial \
+	-device virtserialport,chardev=vm2_qga0,name=org.qemu.guest_agent.2 -daemonize \
+	-monitor unix:/tmp/vm2_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
+	-netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6003-:22 \
+	-chardev socket,id=char0,path=./vhost-net1 \
+	-netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce,queues=8 \
+	-device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:02,disable-modern=false,mrg_rxbuf=on,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on,packed=on -vnc :12
+
+4. On VM1, set virtio device IP and run arp protocal::
+
+	<VM1># ethtool -L ens5 combined 8
+	<VM1># ifconfig ens5 1.1.1.2
+	<VM1># arp -s 1.1.1.8 52:54:00:00:00:02
+
+5. On VM2, set virtio device IP and run arp protocal::
+
+	<VM2># ethtool -L ens5 combined 8
+	<VM2># ifconfig ens5 1.1.1.8
+	<VM2># arp -s 1.1.1.2 52:54:00:00:00:01
+
+6. Scp 1MB file form VM1 to VM2::
+
+	<VM1>: scp <file> root@1.1.1.8:/
+
+7. Check the iperf performance between two VMs by below commands::
+
+	<VM1># iperf -s -i 1
+	<VM2># iperf -c 1.1.1.2 -i 1 -t 60
+
+8. Rerun step 6-7 five times.
+
+Test Case 6: VM2VM vhost-user/virtio-net packed ring non-mergeable path 8 queues test with large packet payload with dsa dpdk driver
+-------------------------------------------------------------------------------------------------------------------------------------
+This case uses iperf and scp to test the payload of large packet (larger than 1MB) is valid after packets forwarding in 
+vm2vm vhost-user/virtio-net packed ring non-mergeable path when vhost uses the asynchronous enqueue and dequeue operations with dsa dpdk driver.
+The dynamic change of multi-queues number also test.
+
+1. Bind 1 dsa device to vfio-pci like common step 1::
+
+	<dpdk dir># ./usertools/dpdk-devbind.py -b vfio-pci f1:01.0 
+
+2. Launch the Vhost sample by below commands::
+
+	<dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 1-5 -n 4 --file-prefix=vhost -a 0000:f1:01.0 \
+	--vdev 'net_vhost0,iface=vhost-net0,queues=8,tso=1,dmas=[txq0;txq1;txq2;txq3;txq4;txq5;rxq2;rxq3;rxq4;rxq5;rxq6;rxq7]' \
+	--vdev 'net_vhost1,iface=vhost-net1,queues=8,tso=1,dmas=[txq2;txq3;txq4;txq5;txq6;txq7;rxq0;rxq1;rxq2;rxq3;rxq4;rxq5]' \
+	--iova=va -- -i --nb-cores=4 --txd=1024 --rxd=1024 --rxq=8 --txq=8 \
+	--lcore-dma=[lcore2@0000:f1:01.0-q0,lcore2@0000:f1:01.0-q1,lcore3@0000:f1:01.0-q2,lcore3@0000:f1:01.0-q3,lcore4@0000:f1:01.0-q4,lcore4@0000:f1:01.0-q5,lcore5@0000:f1:01.0-q6,lcore5@0000:f1:01.0-q7]
+	testpmd>start
+
+3. Launch VM1 and VM2 with qemu::
+
+	<dpdk dir># taskset -c 7 /usr/local/qemu-7.0.0/bin/qemu-system-x86_64 -name vm1 -enable-kvm -cpu host -smp 8 -m 4096 \
+	-object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge,share=on \
+	-numa node,memdev=mem -mem-prealloc -drive file=/home/xingguang/osimg/ubuntu20-04.img  \
+	-chardev socket,path=/tmp/vm1_qga0.sock,server,nowait,id=vm1_qga0 -device virtio-serial \
+	-device virtserialport,chardev=vm1_qga0,name=org.qemu.guest_agent.2 -daemonize \
+	-monitor unix:/tmp/vm1_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
+	-netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6002-:22 \
+	-chardev socket,id=char0,path=./vhost-net0 \
+	-netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce,queues=8 \
+	-device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:01,disable-modern=false,mrg_rxbuf=off,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on,packed=on -vnc :10
+
+	<dpdk dir># taskset -c 8 /usr/local/qemu-7.0.0/bin/qemu-system-x86_64 -name vm2 -enable-kvm -cpu host -smp 8 -m 4096 \
+	-object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge,share=on \
+	-numa node,memdev=mem -mem-prealloc -drive file=/home/xingguang/osimg/ubuntu20-04-2.img  \
+	-chardev socket,path=/tmp/vm2_qga0.sock,server,nowait,id=vm2_qga0 -device virtio-serial \
+	-device virtserialport,chardev=vm2_qga0,name=org.qemu.guest_agent.2 -daemonize \
+	-monitor unix:/tmp/vm2_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
+	-netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6003-:22 \
+	-chardev socket,id=char0,path=./vhost-net1 \
+	-netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce,queues=8 \
+	-device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:02,disable-modern=false,mrg_rxbuf=off,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on,packed=on -vnc :12
+
+4. On VM1, set virtio device IP and run arp protocal::
+
+	<VM1># ethtool -L ens5 combined 8
+	<VM1># ifconfig ens5 1.1.1.2
+	<VM1># arp -s 1.1.1.8 52:54:00:00:00:02
+
+5. On VM2, set virtio device IP and run arp protocal::
+
+	<VM2># ethtool -L ens5 combined 8
+	<VM2># ifconfig ens5 1.1.1.8
+	<VM2># arp -s 1.1.1.2 52:54:00:00:00:01
+
+6. Scp 1MB file form VM1 to VM2::
+
+	<VM1># scp <file> root@1.1.1.8:/
+
+7. Check the iperf performance between two VMs by below commands::
+
+	<VM1># iperf -s -i 1
+	<VM2># iperf -c 1.1.1.2 -i 1 -t 60
+
+8. Rerun step 6-7 five times.
+
+Test Case 7: VM2VM vhost-user/virtio-net packed ring test TSO with dsa dpdk driver and pa mode
+-----------------------------------------------------------------------------------------------
+This case test the function of Vhost tx offload in the topology of vhost-user/virtio-net packed ring mergeable path 
+by verifing the TSO/cksum in the TCP/IP stack when vhost uses the asynchronous enqueue and dequeue operations with dsa dpdk driver and iova as PA mode.
+
+1. Bind 2  dsa device to vfio-pci like common step 1::
+
+	<dpdk dir># ./usertools/dpdk-devbind.py -b vfio-pci f1:01.0 f6:01.0
+
+2. Launch the Vhost sample with PA mode by below commands::
+
+	<dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 2-4 -n 4 --file-prefix=vhost -a 0000:f1:01.0,max_queues=2 \
+	--vdev 'net_vhost0,iface=vhost-net0,queues=1,tso=1,dmas=[txq0;rxq0]' \
+	--vdev 'net_vhost1,iface=vhost-net1,queues=1,tso=1,dmas=[txq0;rxq0]' \
+	--iova=pa -- -i --nb-cores=2 --txd=1024 --rxd=1024 --lcore-dma=[lcore3@0000:f1:01.0-q0,lcore4@0000:f1:01.0-q1]
+	testpmd>start
+
+3. Launch VM1 and VM2 with qemu::
+
+	<dpdk dir># taskset -c 7 /usr/local/qemu-7.0.0/bin/qemu-system-x86_64 -name vm1 -enable-kvm -cpu host -smp 1 -m 4096 \
+	-object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge,share=on \
+	-numa node,memdev=mem -mem-prealloc -drive file=/home/xingguang/osimg/ubuntu20-04.img  \
+	-chardev socket,path=/tmp/vm1_qga0.sock,server,nowait,id=vm1_qga0 -device virtio-serial \
+	-device virtserialport,chardev=vm1_qga0,name=org.qemu.guest_agent.2 -daemonize \
+	-monitor unix:/tmp/vm1_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
+	-netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6002-:22 \
+	-chardev socket,id=char0,path=./vhost-net0 \
+	-netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce \
+	-device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:01,disable-modern=false,mrg_rxbuf=on,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,packed=on -vnc :10
+
+	<dpdk dir># taskset -c 8 /usr/local/qemu-7.0.0/bin/qemu-system-x86_64 -name vm2 -enable-kvm -cpu host -smp 1 -m 4096 \
+	-object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge,share=on \
+	-numa node,memdev=mem -mem-prealloc -drive file=/home/xingguang/osimg/ubuntu20-04-2.img  \
+	-chardev socket,path=/tmp/vm2_qga0.sock,server,nowait,id=vm2_qga0 -device virtio-serial \
+	-device virtserialport,chardev=vm2_qga0,name=org.qemu.guest_agent.2 -daemonize \
+	-monitor unix:/tmp/vm2_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
+	-netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6003-:22 \
+	-chardev socket,id=char0,path=./vhost-net1 \
+	-netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce \
+	-device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:02,disable-modern=false,mrg_rxbuf=on,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,packed=on -vnc :12
+
+4. On VM1, set virtio device IP and run arp protocal::
+
+	<VM1># ifconfig ens5 1.1.1.2
+	<VM1># arp -s 1.1.1.8 52:54:00:00:00:02
+
+5. On VM2, set virtio device IP and run arp protocal::
+
+	<VM2># ifconfig ens5 1.1.1.8
+	<VM2># arp -s 1.1.1.2 52:54:00:00:00:01
+
+6. Check the iperf performance between two VMs by below commands::
+
+	<VM1># iperf -s -i 1
+	<VM2># iperf -c 1.1.1.2 -i 1 -t 60
+
+7. Check that 2VMs can receive and send big packets to each other through vhost log. Port 0 should have tx packets above 1522, Port 1 should have rx packets above 1522::
+
+	testpmd>show port xstats all
+
+Test Case 8: VM2VM vhost-user/virtio-net packed ring mergeable path 8 queues test with large packet payload with dsa dpdk driver and pa mode
+---------------------------------------------------------------------------------------------------------------------------------------------
+This case uses iperf and scp to test the payload of large packet (larger than 1MB) is valid after packets forwarding in 
+vm2vm vhost-user/virtio-net packed ring mergeable path when vhost uses the asynchronous enqueue and dequeue operations with dsa dpdk driver
+and iova as PA mode. 
+
+1. Bind 1 dsa device to vfio-pci like common step 1::
+
+	<dpdk dir># ./usertools/dpdk-devbind.py -b vfio-pci f1:01.0
+
+2. Launch the Vhost sample by below commands::
+
+	<dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 1-5 -n 4 --file-prefix=vhost -a 0000:f1:01.0 \
+	--vdev 'net_vhost0,iface=vhost-net0,queues=8,tso=1,dmas=[txq0;txq1;txq2;txq3;txq4;txq5;txq6;txq7;rxq0;rxq1;rxq2;rxq3;rxq4;rxq5;rxq6;rxq7]' \
+	--vdev 'net_vhost1,iface=vhost-net1,queues=8,tso=1,dmas=[txq0;txq1;txq2;txq3;txq4;txq5;txq6;txq7;rxq0;rxq1;rxq2;rxq3;rxq4;rxq5;rxq6;rxq7]' \
+	--iova=pa -- -i --nb-cores=4 --txd=1024 --rxd=1024 --rxq=8 --txq=8 --lcore-dma=[lcore2@0000:f1:01.0-q0,lcore2@0000:f1:01.0-q1,lcore3@0000:f1:01.0-q2,lcore3@0000:f1:01.0-q3,lcore4@0000:f1:01.0-q4,lcore4@0000:f1:01.0-q5,lcore5@0000:f1:01.0-q6,lcore5@0000:f1:01.0-q7]
+	testpmd>start
+
+3. Launch VM1 and VM2 with qemu::
+
+	<dpdk dir># taskset -c 7 /usr/local/qemu-7.0.0/bin/qemu-system-x86_64 -name vm1 -enable-kvm -cpu host -smp 8 -m 4096 \
+	-object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge,share=on \
+	-numa node,memdev=mem -mem-prealloc -drive file=/home/xingguang/osimg/ubuntu20-04.img  \
+	-chardev socket,path=/tmp/vm1_qga0.sock,server,nowait,id=vm1_qga0 -device virtio-serial \
+	-device virtserialport,chardev=vm1_qga0,name=org.qemu.guest_agent.2 -daemonize \
+	-monitor unix:/tmp/vm1_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
+	-netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6002-:22 \
+	-chardev socket,id=char0,path=./vhost-net0 \
+	-netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce,queues=8 \
+	-device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:01,disable-modern=false,mrg_rxbuf=on,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on,packed=on -vnc :10
+
+	<dpdk dir># taskset -c 8 /usr/local/qemu-7.0.0/bin/qemu-system-x86_64 -name vm2 -enable-kvm -cpu host -smp 8 -m 4096 \
+	-object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge,share=on \
+	-numa node,memdev=mem -mem-prealloc -drive file=/home/xingguang/osimg/ubuntu20-04-2.img  \
+	-chardev socket,path=/tmp/vm2_qga0.sock,server,nowait,id=vm2_qga0 -device virtio-serial \
+	-device virtserialport,chardev=vm2_qga0,name=org.qemu.guest_agent.2 -daemonize \
+	-monitor unix:/tmp/vm2_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
+	-netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6003-:22 \
+	-chardev socket,id=char0,path=./vhost-net1 \
+	-netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce,queues=8 \
+	-device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:02,disable-modern=false,mrg_rxbuf=on,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on,packed=on -vnc :12
+
+4. On VM1, set virtio device IP and run arp protocal::
+
+	<VM1># ethtool -L ens5 combined 8
+	<VM1># ifconfig ens5 1.1.1.2
+	<VM1># arp -s 1.1.1.8 52:54:00:00:00:02
+
+5. On VM2, set virtio device IP and run arp protocal::
+
+	<VM2># ethtool -L ens5 combined 8
+	<VM2># ifconfig ens5 1.1.1.8
+	<VM2># arp -s 1.1.1.2 52:54:00:00:00:01
+
+6. Scp 1MB file form VM1 to VM2::
+
+	<VM1># scp <file> root@1.1.1.8:/
+
+7. Check the iperf performance between two VMs by below commands::
+
+	<VM1># iperf -s -i 1
+	<VM2># iperf -c 1.1.1.2 -i 1 -t 60
+
+8. Rerun step 6-7 five times.
+
+Test Case 9: VM2VM vhost-user/virtio-net split ring test TSO with dsa kernel driver
+------------------------------------------------------------------------------------
+This case test the function of Vhost tx offload in the topology of vhost-user/virtio-net split ring mergeable path 
+by verifing the TSO/cksum in the TCP/IP stack when vhost uses the asynchronous operations with dsa kernel driver.
+
+1. Bind 1 dsa device to idxd like common step 2::
+
+	ls /dev/dsa #check wq configure, reset if exist
+	<dpdk dir># ./usertools/dpdk-devbind.py -u 6a:01.0
+	<dpdk dir># ./usertools/dpdk-devbind.py -b idxd 6a:01.0
+	<dpdk dir># ./drivers/dma/idxd/dpdk_idxd_cfg.py -q 4 0
+	ls /dev/dsa #check wq configure success
+
+2. Launch the Vhost sample by below commands::
+
+	<dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 1-5 -n 4 --file-prefix=vhost \
+	--vdev 'net_vhost0,iface=vhost-net0,queues=1,tso=1,dmas=[txq0;rxq0]' \
+	--vdev 'net_vhost1,iface=vhost-net1,queues=1,tso=1,dmas=[txq0;rxq0]' \
+	--iova=va -- -i --nb-cores=2 --txd=1024 --rxd=1024 --rxq=1 --txq=1 --lcore-dma=[lcore2@wq0.0,lcore2@wq0.1,lcore3@wq0.2,lcore3@wq0.3]
+	testpmd>start
+
+3. Launch VM1 and VM2 on socket 1::
+
+	<dpdk dir># taskset -c 7 /usr/local/qemu-7.0.0/bin/qemu-system-x86_64 -name vm1 -enable-kvm -cpu host -smp 8 -m 4096 \
+	-object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge,share=on \
+	-numa node,memdev=mem -mem-prealloc -drive file=/home/xingguang/osimg/ubuntu20-04.img  \
+	-chardev socket,path=/tmp/vm1_qga0.sock,server,nowait,id=vm1_qga0 -device virtio-serial \
+	-device virtserialport,chardev=vm1_qga0,name=org.qemu.guest_agent.2 -daemonize \
+	-monitor unix:/tmp/vm1_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
+	-netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6002-:22 \
+	-chardev socket,id=char0,path=./vhost-net0 \
+	-netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce \
+	-device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:01,disable-modern=false,mrg_rxbuf=off,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on -vnc :10
+
+	<dpdk dir># taskset -c 8 /usr/local/qemu-7.0.0/bin/qemu-system-x86_64 -name vm2 -enable-kvm -cpu host -smp 8 -m 4096 \
+	-object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge,share=on \
+	-numa node,memdev=mem -mem-prealloc -drive file=/home/xingguang/osimg/ubuntu20-04-2.img  \
+	-chardev socket,path=/tmp/vm2_qga0.sock,server,nowait,id=vm2_qga0 -device virtio-serial \
+	-device virtserialport,chardev=vm2_qga0,name=org.qemu.guest_agent.2 -daemonize \
+	-monitor unix:/tmp/vm2_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
+	-netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6003-:22 \
+	-chardev socket,id=char0,path=./vhost-net1 \
+	-netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce \
+	-device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:02,disable-modern=false,mrg_rxbuf=off,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on -vnc :12
+
+4. On VM1, set virtio device IP and run arp protocal::
+
+	<VM1># ifconfig ens5 1.1.1.2
+	<VM1># arp -s 1.1.1.8 52:54:00:00:00:02
+
+5. On VM2, set virtio device IP and run arp protocal::
+
+	<VM3># ifconfig ens5 1.1.1.8
+	<VM2># arp -s 1.1.1.2 52:54:00:00:00:01
+
+6. Check the iperf performance between two VMs by below commands::
+
+	<VM1># iperf -s -i 1
+	<VM2># iperf -c 1.1.1.2 -i 1 -t 60
+
+7. Check that 2VMs can receive and send big packets to each other through vhost log. Port 0 should have tx packets above 1519, Port 1 should have rx packets above 1519::
+
+	testpmd>show port xstats all
+
+Test Case 10: VM2VM vhost-user/virtio-net split ring mergeable path 8 queues test with large packet payload with dsa kernel driver
+-----------------------------------------------------------------------------------------------------------------------------------
+This case uses iperf and scp to test the payload of large packet (larger than 1MB) is valid after packets forwarding in 
+vm2vm vhost-user/virtio-net split ring mergeable path when vhost uses the asynchronous enqueue and dequeue operations with dsa kernel driver.
+The dynamic change of multi-queues number also test.
+
+1. Bind 2 dsa device to idxd like common step 2::
+
+	ls /dev/dsa #check wq configure, reset if exist
+	<dpdk dir># ./usertools/dpdk-devbind.py -u 6a:01.0 6f:01.0
+	<dpdk dir># ./usertools/dpdk-devbind.py -b idxd 6a:01.0 6f:01.0
+	<dpdk dir># ./drivers/dma/idxd/dpdk_idxd_cfg.py -q 8 0
+	<dpdk dir># ./drivers/dma/idxd/dpdk_idxd_cfg.py -q 8 1
+	ls /dev/dsa #check wq configure success
+
+2. Launch the Vhost sample by below commands::
+
+	<dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 1-5 -n 4 --file-prefix=vhost \
+	--vdev 'net_vhost0,iface=vhost-net0,client=1,queues=8,tso=1,dmas=[txq0;txq1;txq2;txq3;txq4;txq5;txq6;txq7;rxq0;rxq1;rxq2;rxq3;rxq4;rxq5;rxq6;rxq7]' \
+	--vdev 'net_vhost1,iface=vhost-net1,client=1,queues=8,tso=1,dmas=[txq0;txq1;txq2;txq3;txq4;txq5;txq6;txq7;rxq0;rxq1;rxq2;rxq3;rxq4;rxq5;rxq6;rxq7]' \
+	--iova=va -- -i --nb-cores=4 --txd=1024 --rxd=1024 --rxq=8 --txq=8 \
+	--lcore-dma=[lcore2@wq0.0,lcore2@wq0.1,lcore2@wq0.2,lcore2@wq0.3,lcore2@wq0.4,lcore2@wq0.5,lcore3@wq0.6,lcore3@wq0.7,lcore4@wq1.0,lcore4@wq1.1,lcore4@wq1.2,lcore4@wq1.3,lcore4@wq1.4,lcore4@wq1.5,lcore4@wq1.6,lcore5@wq1.7]
+	testpmd>start
+
+3. Launch VM1 and VM2 using qemu::
+
+	<dpdk dir># taskset -c 7 /usr/local/qemu-7.0.0/bin/qemu-system-x86_64 -name vm1 -enable-kvm -cpu host -smp 8 -m 4096 \
+	-object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge,share=on \
+	-numa node,memdev=mem -mem-prealloc -drive file=/home/xingguang/osimg/ubuntu20-04.img  \
+	-chardev socket,path=/tmp/vm1_qga0.sock,server,nowait,id=vm1_qga0 -device virtio-serial \
+	-device virtserialport,chardev=vm1_qga0,name=org.qemu.guest_agent.2 -daemonize \
+	-monitor unix:/tmp/vm1_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
+	-netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6002-:22 \
+	-chardev socket,id=char0,path=./vhost-net0,server \
+	-netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce,queues=8 \
+	-device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:01,disable-modern=false,mrg_rxbuf=on,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on -vnc :10
+
+	<dpdk dir># taskset -c 8 /usr/local/qemu-7.0.0/bin/qemu-system-x86_64 -name vm2 -enable-kvm -cpu host -smp 8 -m 4096 \
+	-object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge,share=on \
+	-numa node,memdev=mem -mem-prealloc -drive file=/home/xingguang/osimg/ubuntu20-04-2.img  \
+	-chardev socket,path=/tmp/vm2_qga0.sock,server,nowait,id=vm2_qga0 -device virtio-serial \
+	-device virtserialport,chardev=vm2_qga0,name=org.qemu.guest_agent.2 -daemonize \
+	-monitor unix:/tmp/vm2_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
+	-netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6003-:22 \
+	-chardev socket,id=char0,path=./vhost-net1,server \
+	-netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce,queues=8 \
+	-device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:02,disable-modern=false,mrg_rxbuf=on,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on -vnc :12
+
+4. On VM1, set virtio device IP and run arp protocal::
+
+	<VM1># ethtool -L ens5 combined 8
+	<VM1># ifconfig ens5 1.1.1.2
+	<VM1># arp -s 1.1.1.8 52:54:00:00:00:02
+
+5. On VM2, set virtio device IP and run arp protocal::
+
+	<VM2># ethtool -L ens5 combined 8
+	<VM2># ifconfig ens5 1.1.1.8
+	<VM2># arp -s 1.1.1.2 52:54:00:00:00:01
+
+6. Scp 1MB file form VM1 to VM2::
+
+	<VM1># scp <file> root@1.1.1.8:/
+
+7. Check the iperf performance between two VMs by below commands::
+
+	<VM1># iperf -s -i 1
+	<VM2># iperf -c 1.1.1.2 -i 1 -t 60
+
+8. Quit and relaunch vhost w/ diff dsa channels::
+
+	<dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 1-5 -n 4 --file-prefix=vhost \
+	--vdev 'net_vhost0,iface=vhost-net0,client=1,queues=8,tso=1,dmas=[txq0;txq1;txq2;txq3;txq4;txq5;rxq2;rxq3;rxq4;rxq5;rxq6;rxq7]' \
+	--vdev 'net_vhost1,iface=vhost-net1,client=1,queues=8,tso=1,dmas=[txq0;txq1;txq2;txq3;txq4;txq5;rxq2;rxq3;rxq4;rxq5;rxq6;rxq7]' \
+	--iova=va -- -i --nb-cores=4 --txd=1024 --rxd=1024 --rxq=8 --txq=8 --lcore-dma=[lcore2@wq0.0,lcore3@wq0.1,lcore4@wq0.2,lcore5@wq0.3]
+	testpmd>start
+
+9. Rerun step 6-7.
+
+10. Quit vhost ports and relaunch vhost ports w/o dsa channels::
+
+	<dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 1-5 -n 4 --file-prefix=vhost --vdev 'net_vhost0,iface=vhost-net0,client=1,tso=1,queues=8' \
+	--vdev 'net_vhost1,iface=vhost-net1,client=1,tso=1,queues=8'  -- -i --nb-cores=4 --txd=1024 --rxd=1024 --rxq=4 --txq=4
+	testpmd>start
+
+11. On VM1, set virtio device::
+
+	ethtool -L ens5 combined 4
+
+12. On VM2, set virtio device::
+
+	ethtool -L ens5 combined 4
+
+13. Rerun step 6-7.
+
+14. Quit vhost ports and relaunch vhost ports with 1 queues::
+
+	<dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 1-5 -n 4 --file-prefix=vhost --vdev 'net_vhost0,iface=vhost-net0,client=1,tso=1,queues=4' \
+	--vdev 'net_vhost1,iface=vhost-net1,client=1,tso=1,queues=4'  -- -i --nb-cores=4 --txd=1024 --rxd=1024 --rxq=1 --txq=1
+	testpmd>start
+
+15. On VM1, set virtio device::
+
+	ethtool -L ens5 combined 1
+
+16. On VM2, set virtio device::
+
+	ethtool -L ens5 combined 1
+
+17. Rerun step 6-7.
+
+Test Case 11: VM2VM vhost-user/virtio-net split ring non-mergeable path 8 queues test with large packet payload with dsa kernel driver
+---------------------------------------------------------------------------------------------------------------------------------------
+This case uses iperf and scp to test the payload of large packet (larger than 1MB) is valid after packets forwarding in 
+vm2vm vhost-user/virtio-net split ring non-mergeable path when vhost uses the asynchronous enqueue and dequeue operations with dsa kernel driver.
+The dynamic change of multi-queues number also test.
+
+1. Bind 1 dsa device to idxd like common step 2::
+
+	ls /dev/dsa #check wq configure, reset if exist
+	<dpdk dir># ./usertools/dpdk-devbind.py -u 6a:01.0 6f:01.0
+	<dpdk dir># ./usertools/dpdk-devbind.py -b idxd 6a:01.0 6f:01.0
+	<dpdk dir># ./drivers/dma/idxd/dpdk_idxd_cfg.py -q 8 0
+	<dpdk dir># ./drivers/dma/idxd/dpdk_idxd_cfg.py -q 8 2
+	ls /dev/dsa #check wq configure success
+
+2. Launch the Vhost sample by below commands::
+
+	<dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 1-5 -n 4 --file-prefix=vhost \
+	--vdev 'net_vhost0,iface=vhost-net0,client=1,queues=8,tso=1,dmas=[txq0;txq1;txq2;txq3;txq4;txq5;rxq2;rxq3;rxq4;rxq5;rxq6;rxq7]' \
+	--vdev 'net_vhost1,iface=vhost-net1,client=1,queues=8,tso=1,dmas=[txq0;txq1;txq2;txq3;txq4;txq5;rxq2;rxq3;rxq4;rxq5;rxq6;rxq7]' \
+	--iova=va -- -i --nb-cores=4 --txd=1024 --rxd=1024 --rxq=8 --txq=8 --lcore-dma=[lcore2@wq0.0,lcore2@wq0.1,lcore3@wq0.2,lcore3@wq0.3,lcore4@wq0.4,lcore4@wq0.5,lcore5@wq0.6,lcore5@wq0.7]
+	testpmd>start
+
+3. Launch VM1 and VM2::
+
+	<dpdk dir># taskset -c 7 /usr/local/qemu-7.0.0/bin/qemu-system-x86_64 -name vm1 -enable-kvm -cpu host -smp 8 -m 4096 \
+	-object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge,share=on \
+	-numa node,memdev=mem -mem-prealloc -drive file=/home/xingguang/osimg/ubuntu20-04.img  \
+	-chardev socket,path=/tmp/vm1_qga0.sock,server,nowait,id=vm1_qga0 -device virtio-serial \
+	-device virtserialport,chardev=vm1_qga0,name=org.qemu.guest_agent.2 -daemonize \
+	-monitor unix:/tmp/vm1_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
+	-netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6002-:22 \
+	-chardev socket,id=char0,path=./vhost-net0,server \
+	-netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce,queues=8 \
+	-device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:01,disable-modern=false,mrg_rxbuf=off,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on -vnc :10
+
+	<dpdk dir># taskset -c 8 /usr/local/qemu-7.0.0/bin/qemu-system-x86_64 -name vm2 -enable-kvm -cpu host -smp 8 -m 4096 \
+	-object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge,share=on \
+	-numa node,memdev=mem -mem-prealloc -drive file=/home/xingguang/osimg/ubuntu20-04-2.img  \
+	-chardev socket,path=/tmp/vm2_qga0.sock,server,nowait,id=vm2_qga0 -device virtio-serial \
+	-device virtserialport,chardev=vm2_qga0,name=org.qemu.guest_agent.2 -daemonize \
+	-monitor unix:/tmp/vm2_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
+	-netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6003-:22 \
+	-chardev socket,id=char0,path=./vhost-net1,server \
+	-netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce,queues=8 \
+	-device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:02,disable-modern=false,mrg_rxbuf=off,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on -vnc :12
+
+4. On VM1, set virtio device IP and run arp protocal::
+
+	<VM1># ethtool -L ens5 combined 8
+	<VM1># ifconfig ens5 1.1.1.2
+	<VM1># arp -s 1.1.1.8 52:54:00:00:00:02
+
+5. On VM2, set virtio device IP and run arp protocal::
+
+	<VM2># ethtool -L ens5 combined 8
+	<VM2># ifconfig ens5 1.1.1.8
+	<VM2># arp -s 1.1.1.2 52:54:00:00:00:01
+
+6. Scp 1MB file form VM1 to VM2::
+
+	<VM1># scp <file> root@1.1.1.8:/
+
+7. Check the iperf performance between two VMs by below commands::
+
+	<VM1># iperf -s -i 1
+	<VM2># iperf -c 1.1.1.2 -i 1 -t 60
+
+8. Quit vhost ports and relaunch vhost ports w/o dsa channels::
+
+	<dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 1-5 -n 4 --file-prefix=vhost --vdev 'net_vhost0,iface=vhost-net0,client=1,tso=1,queues=8' \
+	--vdev 'net_vhost1,iface=vhost-net1,client=1,tso=1,queues=8'  -- -i --nb-cores=4 --txd=1024 --rxd=1024 --rxq=8 --txq=8
+	testpmd>start
+
+9. Rerun step 6-7.
+
+10. Quit vhost ports and relaunch vhost ports with 1 queues::
+
+	<dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 1-5 -n 4 --file-prefix=vhost --vdev 'net_vhost0,iface=vhost-net0,client=1,tso=1,queues=8' \
+	--vdev 'net_vhost1,iface=vhost-net1,client=1,tso=1,queues=8'  -- -i --nb-cores=4 --txd=1024 --rxd=1024 --rxq=1 --txq=1
+	testpmd>start
+
+11. On VM1, set virtio device::
+
+	<VM1># ethtool -L ens5 combined 1
+
+12. On VM2, set virtio device::
+
+	<VM2># ethtool -L ens5 combined 1
+
+13. Rerun step 6-7.
+
+Test Case 12: VM2VM vhost-user/virtio-net packed ring test TSO with dsa kernel driver
+-------------------------------------------------------------------------------------
+This case test the function of Vhost tx offload in the topology of vhost-user/virtio-net packed ring mergeable path
+by verifing the TSO/cksum in the TCP/IP stack when vhost uses the asynchronous enqueue and dequeue operations with dsa kernel driver.
+
+1. Bind 2 dsa device to idxd::
+
+	ls /dev/dsa #check wq configure, reset if exist
+	<dpdk dir># ./usertools/dpdk-devbind.py -u 6a:01.0 6f:01.0
+	<dpdk dir># ./usertools/dpdk-devbind.py -b idxd 6a:01.0 6f:01.0
+	<dpdk dir># ./drivers/dma/idxd/dpdk_idxd_cfg.py -q 1 0
+	<dpdk dir># ./drivers/dma/idxd/dpdk_idxd_cfg.py -q 1 2
+	ls /dev/dsa #check wq configure success
+
+2. Launch the Vhost sample by below commands::
+
+	<dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 2-4 -n 4 --file-prefix=vhost \
+	--vdev 'net_vhost0,iface=vhost-net0,queues=1,tso=1,dmas=[txq0;rxq0]' \
+	--vdev 'net_vhost1,iface=vhost-net1,queues=1,tso=1,dmas=[txq0;rxq0]' \
+	--iova=va -- -i --nb-cores=2 --txd=1024 --rxd=1024 --lcore-dma=[lcore3@wq0.0,lcore4@wq1.0]
+	testpmd>start
+
+3. Launch VM1 and VM2 with qemu::
+
+	<dpdk dir># taskset -c 7 /usr/local/qemu-7.0.0/bin/qemu-system-x86_64 -name vm1 -enable-kvm -cpu host -smp 1 -m 4096 \
+	-object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge,share=on \
+	-numa node,memdev=mem -mem-prealloc -drive file=/home/xingguang/osimg/ubuntu20-04.img  \
+	-chardev socket,path=/tmp/vm1_qga0.sock,server,nowait,id=vm1_qga0 -device virtio-serial \
+	-device virtserialport,chardev=vm1_qga0,name=org.qemu.guest_agent.2 -daemonize \
+	-monitor unix:/tmp/vm1_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
+	-netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6002-:22 \
+	-chardev socket,id=char0,path=./vhost-net0 \
+	-netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce \
+	-device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:01,disable-modern=false,mrg_rxbuf=on,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,packed=on -vnc :10
+
+	<dpdk dir># taskset -c 8 /usr/local/qemu-7.0.0/bin/qemu-system-x86_64 -name vm2 -enable-kvm -cpu host -smp 1 -m 4096 \
+	-object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge,share=on \
+	-numa node,memdev=mem -mem-prealloc -drive file=/home/xingguang/osimg/ubuntu20-04-2.img  \
+	-chardev socket,path=/tmp/vm2_qga0.sock,server,nowait,id=vm2_qga0 -device virtio-serial \
+	-device virtserialport,chardev=vm2_qga0,name=org.qemu.guest_agent.2 -daemonize \
+	-monitor unix:/tmp/vm2_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
+	-netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6003-:22 \
+	-chardev socket,id=char0,path=./vhost-net1 \
+	-netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce \
+	-device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:02,disable-modern=false,mrg_rxbuf=on,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,packed=on -vnc :12
+
+4. On VM1, set virtio device IP and run arp protocal::
+
+	<VM1># ifconfig ens5 1.1.1.2
+	<VM1># arp -s 1.1.1.8 52:54:00:00:00:02
+
+5. On VM2, set virtio device IP and run arp protocal::
+
+	<VM2># ifconfig ens5 1.1.1.8
+	<VM2># arp -s 1.1.1.2 52:54:00:00:00:01
+
+6. Check the iperf performance between two VMs by below commands::
+
+	<VM1># iperf -s -i 1
+	<VM2># iperf -c 1.1.1.2 -i 1 -t 60
+
+7. Check that 2VMs can receive and send big packets to each other through vhost log. Port 0 should have tx packets above 1522, Port 1 should have rx packets above 1522::
+
+	testpmd>show port xstats all
+
+Test Case 13: VM2VM vhost-user/virtio-net packed ring mergeable path 8 queues test with large packet payload with dsa kernel driver
+-------------------------------------------------------------------------------------------------------------------------------------
+This case uses iperf and scp to test the payload of large packet (larger than 1MB) is valid after packets forwarding in
+vm2vm vhost-user/virtio-net packed ring mergeable path when vhost uses the asynchronous enqueue and dequeue operations with dsa kernel driver.
+The dynamic change of multi-queues number also test.
+
+1. Bind 1 dsa device to idxd like common step 2::
+
+	ls /dev/dsa #check wq configure, reset if exist
+	<dpdk dir># ./usertools/dpdk-devbind.py -u 6a:01.0 6f:01.0 
+	<dpdk dir># ./usertools/dpdk-devbind.py -b idxd 6a:01.0 6f:01.0 
+	<dpdk dir># ./drivers/dma/idxd/dpdk_idxd_cfg.py -q 8 0
+
+2. Launch the Vhost sample by below commands::
+
+	<dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 1-5 -n 4 --file-prefix=vhost \
+	--vdev 'net_vhost0,iface=vhost-net0,queues=8,tso=1,dmas=[txq0;txq1;txq2;txq3;txq4;txq5;rxq2;rxq3;rxq4;rxq5;rxq6;rxq7]' \
+	--vdev 'net_vhost1,iface=vhost-net1,queues=8,tso=1,dmas=[txq0;txq1;txq2;txq3;txq4;txq5;rxq2;rxq3;rxq4;rxq5;rxq6;rxq7]' \
+	--iova=va -- -i --nb-cores=4 --txd=1024 --rxd=1024 --rxq=8 --txq=8 --lcore-dma=[lcore2@wq0.0,lcore2@wq0.1,lcore3@wq0.2,lcore3@wq0.3,lcore4@wq0.4,lcore4@wq0.5,lcore5@wq0.6,lcore5@wq0.7]
+	testpmd>start
+
+3. Launch VM1 and VM2 with qemu::
+
+	<dpdk dir># taskset -c 7 /usr/local/qemu-7.0.0/bin/qemu-system-x86_64 -name vm1 -enable-kvm -cpu host -smp 8 -m 4096 \
+	-object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge,share=on \
+	-numa node,memdev=mem -mem-prealloc -drive file=/home/xingguang/osimg/ubuntu20-04.img  \
+	-chardev socket,path=/tmp/vm1_qga0.sock,server,nowait,id=vm1_qga0 -device virtio-serial \
+	-device virtserialport,chardev=vm1_qga0,name=org.qemu.guest_agent.2 -daemonize \
+	-monitor unix:/tmp/vm1_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
+	-netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6002-:22 \
+	-chardev socket,id=char0,path=./vhost-net0 \
+	-netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce,queues=8 \
+	-device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:01,disable-modern=false,mrg_rxbuf=on,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on,packed=on -vnc :10
+
+	<dpdk dir># taskset -c 8 /usr/local/qemu-7.0.0/bin/qemu-system-x86_64 -name vm2 -enable-kvm -cpu host -smp 8 -m 4096 \
+	-object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge,share=on \
+	-numa node,memdev=mem -mem-prealloc -drive file=/home/xingguang/osimg/ubuntu20-04-2.img  \
+	-chardev socket,path=/tmp/vm2_qga0.sock,server,nowait,id=vm2_qga0 -device virtio-serial \
+	-device virtserialport,chardev=vm2_qga0,name=org.qemu.guest_agent.2 -daemonize \
+	-monitor unix:/tmp/vm2_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
+	-netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6003-:22 \
+	-chardev socket,id=char0,path=./vhost-net1 \
+	-netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce,queues=8 \
+	-device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:02,disable-modern=false,mrg_rxbuf=on,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on,packed=on -vnc :12
+
+4. On VM1, set virtio device IP and run arp protocal::
+
+	<VM1># ethtool -L ens5 combined 8
+	<VM1># ifconfig ens5 1.1.1.2
+	<VM1># arp -s 1.1.1.8 52:54:00:00:00:02
+
+5. On VM2, set virtio device IP and run arp protocal::
+
+	<VM2># ethtool -L ens5 combined 8
+	<VM2># ifconfig ens5 1.1.1.8
+	<VM2># arp -s 1.1.1.2 52:54:00:00:00:01
+
+6. Scp 1MB file form VM1 to VM2::
+
+	<VM1># scp <file> root@1.1.1.8:/
+
+7. Check the iperf performance between two VMs by below commands::
+
+	<VM1># iperf -s -i 1
+	<VM2># iperf -c 1.1.1.2 -i 1 -t 60
+
+8. Rerun step 6-7 five times.
+
+Test Case 14: VM2VM vhost-user/virtio-net packed ring non-mergeable path 8 queues test with large packet payload with dsa kernel driver
+----------------------------------------------------------------------------------------------------------------------------------------
+This case uses iperf and scp to test the payload of large packet (larger than 1MB) is valid after packets forwarding in
+vm2vm vhost-user/virtio-net packed ring mergeable path when vhost uses the asynchronous enqueue and dequeue operations with dsa kernel driver.
+
+1. Bind 2 dsa device to vfio-pci like common step 2::
+
+	ls /dev/dsa #check wq configure, reset if exist
+	<dpdk dir># ./usertools/dpdk-devbind.py -u 6a:01.0 6f:01.0 
+	<dpdk dir># ./usertools/dpdk-devbind.py -b idxd 6a:01.0 6f:01.0 
+	<dpdk dir># ./drivers/dma/idxd/dpdk_idxd_cfg.py -q 4 0
+	<dpdk dir># ./drivers/dma/idxd/dpdk_idxd_cfg.py -q 4 1
+	ls /dev/dsa #check wq configure success
+
+2. Launch the Vhost sample by below commands::
+
+	<dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 1-5 -n 4 --file-prefix=vhost \
+	--vdev 'net_vhost0,iface=vhost-net0,queues=8,tso=1,dmas=[txq0;txq1;txq2;txq3;txq4;txq5;txq6;txq7;rxq0;rxq1;rxq2;rxq3;rxq4;rxq5;rxq6;rxq7]' \
+	--vdev 'net_vhost1,iface=vhost-net1,queues=8,tso=1,dmas=[txq0;txq1;txq2;txq3;txq4;txq5;txq6;txq7;rxq0;rxq1;rxq2;rxq3;rxq4;rxq5;rxq6;rxq7]' \
+	--iova=va -- -i --nb-cores=4 --txd=1024 --rxd=1024 --rxq=8 --txq=8 --lcore-dma=[lcore2@wq0.0,lcore2@wq0.1,lcore3@wq0.2,lcore3@wq0.3,lcore4@wq1.0,lcore4@wq1.1,lcore5@wq1.2,lcore5@wq1.3]
+	testpmd>start
+
+3. Launch VM1 and VM2 with qemu::
+
+	<dpdk dir># taskset -c 7 /usr/local/qemu-7.0.0/bin/qemu-system-x86_64 -name vm1 -enable-kvm -cpu host -smp 8 -m 4096 \
+	-object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge,share=on \
+	-numa node,memdev=mem -mem-prealloc -drive file=/home/xingguang/osimg/ubuntu20-04.img  \
+	-chardev socket,path=/tmp/vm1_qga0.sock,server,nowait,id=vm1_qga0 -device virtio-serial \
+	-device virtserialport,chardev=vm1_qga0,name=org.qemu.guest_agent.2 -daemonize \
+	-monitor unix:/tmp/vm1_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
+	-netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6002-:22 \
+	-chardev socket,id=char0,path=./vhost-net0 \
+	-netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce,queues=8 \
+	-device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:01,disable-modern=false,mrg_rxbuf=off,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on,packed=on -vnc :10
+
+	<dpdk dir># taskset -c 8 /usr/local/qemu-7.0.0/bin/qemu-system-x86_64 -name vm2 -enable-kvm -cpu host -smp 8 -m 4096 \
+	-object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge,share=on \
+	-numa node,memdev=mem -mem-prealloc -drive file=/home/xingguang/osimg/ubuntu20-04-2.img  \
+	-chardev socket,path=/tmp/vm2_qga0.sock,server,nowait,id=vm2_qga0 -device virtio-serial \
+	-device virtserialport,chardev=vm2_qga0,name=org.qemu.guest_agent.2 -daemonize \
+	-monitor unix:/tmp/vm2_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
+	-netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6003-:22 \
+	-chardev socket,id=char0,path=./vhost-net1 \
+	-netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce,queues=8 \
+	-device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:02,disable-modern=false,mrg_rxbuf=off,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on,packed=on -vnc :12
+
+4. On VM1, set virtio device IP and run arp protocal::
+
+	<VM1># ethtool -L ens5 combined 8
+	<VM1># ifconfig ens5 1.1.1.2
+	<VM1># arp -s 1.1.1.8 52:54:00:00:00:02
+
+5. On VM2, set virtio device IP and run arp protocal::
+
+	<VM2># ethtool -L ens5 combined 8
+	<VM2># ifconfig ens5 1.1.1.8
+	<VM2># arp -s 1.1.1.2 52:54:00:00:00:01
+
+6. Scp 1MB file form VM1 to VM2::
+
+	<VM1># scp <file> root@1.1.1.8:/
+
+7. Check the iperf performance between two VMs by below commands::
+
+	<VM1># iperf -s -i 1
+	<VM2># iperf -c 1.1.1.2 -i 1 -t 60
+
+8. Rerun step 6-7 five times.
+
+Test Case 15: VM2VM vhost-user/virtio-net split ring non-mergeable 16 queues test with large packet payload with dsa dpdk and kernel driver
+--------------------------------------------------------------------------------------------------------------------------------------------
+This case uses iperf and scp to test the payload of large packet (larger than 1MB) is valid after packets forwarding in
+vm2vm vhost-user/virtio-net split ring non-mergeable path when vhost uses the asynchronous operations with dsa dpdk
+and kernel driver. The dynamic change of multi-queues number also test.
+
+1. Bind 2 dsa device to vfio-pci and 2 dsa device to idxd like common step 1-2::
+
+	ls /dev/dsa #check wq configure, reset if exist
+	<dpdk dir># ./usertools/dpdk-devbind.py -u 6a:01.0 6f:01.0 
+	<dpdk dir># ./usertools/dpdk-devbind.py -b idxd 6a:01.0 6f:01.0 
+	<dpdk dir># ./drivers/dma/idxd/dpdk_idxd_cfg.py -q 8 0
+	<dpdk dir># ./drivers/dma/idxd/dpdk_idxd_cfg.py -q 8 1
+	ls /dev/dsa #check wq configure success
+
+	<dpdk dir># ./usertools/dpdk-devbind.py -u 0000:e7:01.0 0000:ec:01.0 
+	<dpdk dir># ./usertools/dpdk-devbind.py -b vfio-pci 0000:f1:01.0 0000:f6:01.0
+
+2. Launch the Vhost sample by below commands::
+
+	<dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 1-5 -n 4 --file-prefix=vhost -a 0000:f1:01.0 -a 0000:f6:01.0  \
+	--vdev 'net_vhost0,iface=vhost-net0,client=1,queues=16,tso=1,dmas=[txq0;txq1;txq2;txq3;txq4;txq5;txq6;txq7;txq8;txq9;txq10;txq11;txq12;txq13;txq14;txq15;rxq0;rxq1;rxq2;rxq3;rxq4;rxq5;rxq6;rxq7;rxq8;rxq9;rxq10;rxq11;rxq12;rxq13;rxq14;rxq15]' \
+	--vdev 'net_vhost1,iface=vhost-net1,client=1,queues=16,tso=1,dmas=[txq0;txq1;txq2;txq3;txq4;txq5;txq6;txq7;txq8;txq9;txq10;txq11;txq12;txq13;txq14;txq15;rxq0;rxq1;rxq2;rxq3;rxq4;rxq5;rxq6;rxq7;rxq8;rxq9;rxq10;rxq11;rxq12;rxq13;rxq14;rxq15]' \
+	--iova=va -- -i --nb-cores=4 --txd=1024 --rxd=1024 --rxq=16 --txq=16 --lcore-dma=[lcore2@0000:f1:01.0-q0,lcore2@0000:f1:01.0-q1,lcore3@0000:f6:01.0-q0,lcore3@0000:f6:01.0-q1,lcore4@wq0.0,lcore5@wq0.1]
+	testpmd>start
+
+3. Launch VM1 and VM2::
+
+	<dpdk dir># taskset -c 7 /usr/local/qemu-7.0.0/bin/qemu-system-x86_64 -name vm1 -enable-kvm -cpu host -smp 8 -m 4096 \
+	-object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge,share=on \
+	-numa node,memdev=mem -mem-prealloc -drive file=/home/xingguang/osimg/ubuntu20-04.img  \
+	-chardev socket,path=/tmp/vm1_qga0.sock,server,nowait,id=vm1_qga0 -device virtio-serial \
+	-device virtserialport,chardev=vm1_qga0,name=org.qemu.guest_agent.2 -daemonize \
+	-monitor unix:/tmp/vm1_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
+	-netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6002-:22 \
+	-chardev socket,id=char0,path=./vhost-net0,server \
+	-netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce,queues=16 \
+	-device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:01,disable-modern=false,mrg_rxbuf=off,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on -vnc :10
+
+	<dpdk dir># taskset -c 8 /usr/local/qemu-7.0.0/bin/qemu-system-x86_64 -name vm2 -enable-kvm -cpu host -smp 8 -m 4096 \
+	-object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge,share=on \
+	-numa node,memdev=mem -mem-prealloc -drive file=/home/xingguang/osimg/ubuntu20-04-2.img  \
+	-chardev socket,path=/tmp/vm2_qga0.sock,server,nowait,id=vm2_qga0 -device virtio-serial \
+	-device virtserialport,chardev=vm2_qga0,name=org.qemu.guest_agent.2 -daemonize \
+	-monitor unix:/tmp/vm2_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
+	-netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6003-:22 \
+	-chardev socket,id=char0,path=./vhost-net1,server \
+	-netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce,queues=16 \
+	-device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:02,disable-modern=false,mrg_rxbuf=off,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on -vnc :12
+
+4. On VM1, set virtio device IP and run arp protocal::
+
+	<VM1># ethtool -L ens5 combined 16
+	<VM1># ifconfig ens5 1.1.1.2
+	<VM1># arp -s 1.1.1.8 52:54:00:00:00:02
+
+5. On VM2, set virtio device IP and run arp protocal::
+
+	<VM2># ethtool -L ens5 combined 16
+	<VM2># ifconfig ens5 1.1.1.8
+	<VM2># arp -s 1.1.1.2 52:54:00:00:00:01
+
+6. Scp 1MB file form VM1 to VM2::
+
+	<VM1># scp <file> root@1.1.1.8:/
+
+7. Check the iperf performance between two VMs by below commands::
+
+	<VM1># iperf -s -i 1
+	<VM2># iperf -c 1.1.1.2 -i 1 -t 60
+
+8. Quit vhost ports and relaunch vhost ports w/ diff dsa channels::
+
+	<dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 1-5 -n 4 --file-prefix=vhost -a 0000:f1:01.0,max_queues=2 \
+	--vdev 'net_vhost0,iface=vhost-net0,client=1,queues=16,tso=1,dmas=[txq0;txq1;txq2;txq3;txq4;txq5;rxq2;rxq3;rxq4;rxq5;rxq6;rxq7]' \
+	--vdev 'net_vhost1,iface=vhost-net1,client=1,queues=16,tso=1,dmas=[txq10;txq11;txq12;txq13;txq14;txq15;rxq10;rxq11;rxq12;rxq13;rxq14;rxq15]' \
+	--iova=va -- -i --nb-cores=4 --txd=1024 --rxd=1024 --rxq=16 --txq=16 --lcore-dma=[lcore2@0000:f1:01.0-q0,lcore2@wq0.0,lcore3@0000:f1:01.0-q1,lcore3@wq0.1,lcore4@wq1.0,lcore5@wq1.1]
+	testpmd>start
+
+9. rerun step 6-7.
+
+10. Quit vhost ports and relaunch vhost ports w/o dsa channels::
+
+	<dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 1-5 -n 4 --file-prefix=vhost --vdev 'net_vhost0,iface=vhost-net0,client=1,tso=1,queues=16' \
+	--vdev 'net_vhost1,iface=vhost-net1,client=1,tso=1,queues=16'  -- -i --nb-cores=4 --txd=1024 --rxd=1024 --rxq=16 --txq=16
+	testpmd>start
+
+11. Rerun step 6-7.
+
+12. Quit vhost ports and relaunch vhost ports with 1 queues::
+
+	<dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 1-5 -n 4 --file-prefix=vhost --vdev 'net_vhost0,iface=vhost-net0,client=1,tso=1,queues=8' \
+	--vdev 'net_vhost1,iface=vhost-net1,client=1,tso=1,queues=8'  -- -i --nb-cores=4 --txd=1024 --rxd=1024 --rxq=1 --txq=1
+	testpmd>start
+
+13. On VM1, set virtio device::
+
+	<VM1># ethtool -L ens5 combined 1
+
+14. On VM2, set virtio device::
+
+	<VM2># ethtool -L ens5 combined 1
+
+15. Rerun step 6-7.
+
+Test Case 16: VM2VM vhost-user/virtio-net packed ring mergeable 16 queues test with large packet payload with dsa dpdk and kernel driver
+------------------------------------------------------------------------------------------------------------------------------------------
+This case uses iperf and scp to test the payload of large packet (larger than 1MB) is valid after packets forwarding in
+vm2vm vhost-user/virtio-net packed ring mergeable path when vhost uses the asynchronous operations with dsa dpdk
+and kernel driver. The dynamic change of multi-queues number also test.
+
+1. Bind 2 dsa device to vfio-pci and 2 dsa device to idxd like common step 1-2::
+
+	ls /dev/dsa #check wq configure, reset if exist
+
+	<dpdk dir># ./usertools/dpdk-devbind.py -u 6a:01.0 6f:01.0 
+	<dpdk dir># ./usertools/dpdk-devbind.py -b idxd 6a:01.0 6f:01.0 
+	<dpdk dir># ./usertools/dpdk-devbind.py -b vfio-pci f1:01.0 f6:01.0
+	<dpdk dir># ./drivers/dma/idxd/dpdk_idxd_cfg.py -q 2 0
+	<dpdk dir># ./drivers/dma/idxd/dpdk_idxd_cfg.py -q 2 1
+	ls /dev/dsa #check wq configure success
+
+2. Launch the Vhost sample by below commands::
+
+	<dpdk dir># ./x86_64-native-linuxapp-gcc/app/dpdk-testpmd -l 1-5 -n 4 --file-prefix=vhost -a 0000:f1:01.0,max_queues=1 -a 0000:f6:01.0,max_queues=1 \
+	--vdev 'net_vhost0,iface=vhost-net0,queues=16,tso=1,dmas=[txq0;txq1;txq2;txq3;txq4;txq5;txq6;txq7;txq8;txq9;txq10;txq11;txq12;txq13;txq14;txq15;rxq0;rxq1;rxq2;rxq3;rxq4;rxq5;rxq6;rxq7;rxq8;rxq9;rxq10;rxq11;rxq12;rxq13;rxq14;rxq15]' \
+	--vdev 'net_vhost1,iface=vhost-net1,queues=16,tso=1,dmas=[txq0;txq1;txq2;txq3;txq4;txq5;txq6;txq7;txq8;txq9;txq10;txq11;txq12;txq13;txq14;txq15;rxq0;rxq1;rxq2;rxq3;rxq4;rxq5;rxq6;rxq7;rxq8;rxq9;rxq10;rxq11;rxq12;rxq13;rxq14;rxq15]' \
+	--iova=va -- -i --nb-cores=4 --txd=1024 --rxd=1024 --rxq=16 --txq=16 --lcore-dma=[lcore2@0000:f1:01.0-q0,lcore2@wq0.0,lcore3@0000:f6:01.0-q0,lcore3@wq0.1,lcore4@wq1.0,lcore5@wq1.1]
+	testpmd>start
+
+3. Launch VM1 and VM2 with qemu::
+
+	<dpdk dir># taskset -c 7 /usr/local/qemu-7.0.0/bin/qemu-system-x86_64 -name vm1 -enable-kvm -cpu host -smp 8 -m 4096 \
+	-object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge,share=on \
+	-numa node,memdev=mem -mem-prealloc -drive file=/home/xingguang/osimg/ubuntu20-04.img  \
+	-chardev socket,path=/tmp/vm1_qga0.sock,server,nowait,id=vm1_qga0 -device virtio-serial \
+	-device virtserialport,chardev=vm1_qga0,name=org.qemu.guest_agent.2 -daemonize \
+	-monitor unix:/tmp/vm1_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
+	-netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6002-:22 \
+	-chardev socket,id=char0,path=./vhost-net0 \
+	-netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce,queues=16 \
+	-device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:01,disable-modern=false,mrg_rxbuf=on,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on,packed=on -vnc :10
+
+	<dpdk dir># taskset -c 8 /usr/local/qemu-7.0.0/bin/qemu-system-x86_64 -name vm2 -enable-kvm -cpu host -smp 8 -m 4096 \
+	-object memory-backend-file,id=mem,size=4096M,mem-path=/mnt/huge,share=on \
+	-numa node,memdev=mem -mem-prealloc -drive file=/home/xingguang/osimg/ubuntu20-04-2.img  \
+	-chardev socket,path=/tmp/vm2_qga0.sock,server,nowait,id=vm2_qga0 -device virtio-serial \
+	-device virtserialport,chardev=vm2_qga0,name=org.qemu.guest_agent.2 -daemonize \
+	-monitor unix:/tmp/vm2_monitor.sock,server,nowait -device e1000,netdev=nttsip1 \
+	-netdev user,id=nttsip1,hostfwd=tcp:127.0.0.1:6003-:22 \
+	-chardev socket,id=char0,path=./vhost-net1 \
+	-netdev type=vhost-user,id=netdev0,chardev=char0,vhostforce,queues=16 \
+	-device virtio-net-pci,netdev=netdev0,mac=52:54:00:00:00:02,disable-modern=false,mrg_rxbuf=on,mq=on,vectors=40,csum=on,guest_csum=on,host_tso4=on,guest_tso4=on,guest_ecn=on,guest_ufo=on,host_ufo=on,packed=on -vnc :12
+
+4. On VM1, set virtio device IP and run arp protocal::
+
+	<VM1># ethtool -L ens5 combined 16
+	<VM1># ifconfig ens5 1.1.1.2
+	<VM1># arp -s 1.1.1.8 52:54:00:00:00:02
+
+5. On VM2, set virtio device IP and run arp protocal::
+
+	<VM2># ethtool -L ens5 combined 16
+	<VM2># ifconfig ens5 1.1.1.8
+	<VM2># arp -s 1.1.1.2 52:54:00:00:00:01
+
+6. Scp 1MB file form VM1 to VM2::
+
+	<VM1># scp <file> root@1.1.1.8:/
+
+7. Check the iperf performance between two VMs by below commands::
+
+	<VM1># iperf -s -i 1
+	<VM2># iperf -c 1.1.1.2 -i 1 -t 60
+
+8. Rerun step 6-7 five times.
+
+
+
