diff mbox series

[V1,2/4] test_plans/generic_flow_api_test_plan: move case from generic_filter to generic_flow_api

Message ID 20210929182832.146624-3-yanx.xia@intel.com (mailing list archive)
State Accepted
Headers
Series *** move case from generic_filter to generic_flow_api *** |

Commit Message

Yan Xia Sept. 29, 2021, 6:28 p.m. UTC 
  move case from generic_filter to generic_flow_api

Signed-off-by: Yan Xia <yanx.xia@intel.com>
---
 test_plans/generic_flow_api_test_plan.rst | 37 +++++++++++++++++++++++
 1 file changed, 37 insertions(+)
diff mbox series

Patch

diff --git a/test_plans/generic_flow_api_test_plan.rst b/test_plans/generic_flow_api_test_plan.rst
index 760f8e82..d3029430 100644
--- a/test_plans/generic_flow_api_test_plan.rst
+++ b/test_plans/generic_flow_api_test_plan.rst
@@ -2154,3 +2154,40 @@  Configure the traffic generator to send syn packets. Then Verify that
 the packet are not received on the queue 2::
 
     testpmd> stop
+
+Test Case: 128 queues
+========================
+
+This case is designed for NIC(niantic). Since NIC(niantic) has 128 transmit
+queues, it should be supports 128 kinds of filter if Hardware have enough
+cores.
+DPDK enable 64 queues in ixgbe driver by default. Enlarge queue number to 128
+for 128 queues test::
+
+    sed -i -e 's/#define IXGBE_NONE_MODE_TX_NB_QUEUES 64$/#define IXGBE_NONE_MODE_TX_NB_QUEUES 128/' drivers/net/ixgbe/ixgbe_ethdev.h
+
+Launch the app ``testpmd`` with the following arguments::
+
+    ./testpmd -l 1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,37,38,39,40,41,42,43,44,45,46,47,48,49,50,51,52,53 -n 4 -- -i --disable-rss --rxq=128 --txq=128 --portmask=0x3 --nb-cores=4      --total-num-mbufs=263168
+
+    testpmd>set stat_qmap rx 0 0 0
+    testpmd>set stat_qmap rx 1 0 0
+    testpmd>vlan set strip off 0
+    testpmd>vlan set strip off 1
+    testpmd>vlan set filter off 0
+    testpmd>vlan set filter off 1
+
+Create the 5-tuple Filters with different queues (64,127) on port 0 for
+niantic::
+
+    testpmd> set stat_qmap rx 0 64 1
+    testpmd> flow create 0 ingress pattern eth / ipv4 dst is 2.2.2.5 src is 2.2.2.4 / tcp dst is 1 src is 1 / end actions queue index 64 / end
+    testpmd> set stat_qmap rx 0 127 2
+    testpmd> flow create 0 ingress pattern eth / ipv4 dst is 2.2.2.5 src is 2.2.2.4 / tcp dst is 2 src is 1 / end actions queue index 127 / end
+
+Send packets(`dst_ip` = 2.2.2.5 `src_ip` = 2.2.2.4 `dst_port` = 1 `src_port` =
+1 `protocol` = tcp) and (`dst_ip` = 2.2.2.5 `src_ip` = 2.2.2.4 `dst_port` = 2
+`src_port` = 1 `protocol` = tcp ). Then reading the stats for port 0 after
+sending packets. packets are received on the queue 64 and queue 127 When
+setting 5-tuple Filter with queue(128), it will display failure because the
+number of queues no more than 128.