net/ixgbe: add support of loopback for X540/X550
Checks
Commit Message
Loopback mode is also supported on X540 and X550 NICs, according to
their datasheet (section 15.2). The way to set it up is a little
different of the 82599.
Signed-off-by: Julien Meunier <julien.meunier@nokia.com>
---
drivers/net/ixgbe/ixgbe_ethdev.c | 10 ++++++---
drivers/net/ixgbe/ixgbe_ethdev.h | 5 ++---
drivers/net/ixgbe/ixgbe_rxtx.c | 47 ++++++++++++++++++++++++++++++++++------
3 files changed, 49 insertions(+), 13 deletions(-)
Comments
> -----Original Message-----
> From: dev [mailto:dev-bounces@dpdk.org] On Behalf Of Julien Meunier
> Sent: Thursday, January 3, 2019 12:01 AM
> To: Ananyev, Konstantin <konstantin.ananyev@intel.com>; Lu, Wenzhuo
> <wenzhuo.lu@intel.com>
> Cc: dev@dpdk.org
> Subject: [dpdk-dev] [PATCH] net/ixgbe: add support of loopback for X540/X550
>
> Loopback mode is also supported on X540 and X550 NICs, according to their
> datasheet (section 15.2). The way to set it up is a little different of the 82599.
Thanks for enable this.
one question is, Datasheet also mentioned that auto negotiation should be disabled
but I didn't see any related change with it.
Would you share more insight on this?
>
> Signed-off-by: Julien Meunier <julien.meunier@nokia.com>
> ---
> drivers/net/ixgbe/ixgbe_ethdev.c | 10 ++++++---
> drivers/net/ixgbe/ixgbe_ethdev.h | 5 ++---
> drivers/net/ixgbe/ixgbe_rxtx.c | 47
> ++++++++++++++++++++++++++++++++++------
> 3 files changed, 49 insertions(+), 13 deletions(-)
>
> diff --git a/drivers/net/ixgbe/ixgbe_ethdev.c
> b/drivers/net/ixgbe/ixgbe_ethdev.c
> index 7493110..7eb3303 100644
> --- a/drivers/net/ixgbe/ixgbe_ethdev.c
> +++ b/drivers/net/ixgbe/ixgbe_ethdev.c
> @@ -2652,9 +2652,13 @@ ixgbe_dev_start(struct rte_eth_dev *dev)
> goto error;
> }
>
> - /* Skip link setup if loopback mode is enabled for 82599. */
> - if (hw->mac.type == ixgbe_mac_82599EB &&
> - dev->data->dev_conf.lpbk_mode == IXGBE_LPBK_82599_TX_RX)
> + /* Skip link setup if loopback mode is enabled. */
> + if ((hw->mac.type == ixgbe_mac_82599EB ||
> + hw->mac.type == ixgbe_mac_X540 ||
> + hw->mac.type == ixgbe_mac_X550 ||
> + hw->mac.type == ixgbe_mac_X550EM_x ||
> + hw->mac.type == ixgbe_mac_X550EM_a) &&
> + dev->data->dev_conf.lpbk_mode == IXGBE_LPBK_TX_RX)
> goto skip_link_setup;
>
> if (ixgbe_is_sfp(hw) && hw->phy.multispeed_fiber) { diff --git
> a/drivers/net/ixgbe/ixgbe_ethdev.h b/drivers/net/ixgbe/ixgbe_ethdev.h
> index 565c69c..c60a697 100644
> --- a/drivers/net/ixgbe/ixgbe_ethdev.h
> +++ b/drivers/net/ixgbe/ixgbe_ethdev.h
> @@ -65,9 +65,8 @@
> #define IXGBE_QUEUE_ITR_INTERVAL_DEFAULT 500 /* 500us */
>
> /* Loopback operation modes */
> -/* 82599 specific loopback operation types */
> -#define IXGBE_LPBK_82599_NONE 0x0 /* Default value. Loopback is disabled.
> */
> -#define IXGBE_LPBK_82599_TX_RX 0x1 /* Tx->Rx loopback operation is
> enabled. */
> +#define IXGBE_LPBK_NONE 0x0 /* Default value. Loopback is disabled. */
> +#define IXGBE_LPBK_TX_RX 0x1 /* Tx->Rx loopback operation is enabled.
> +*/
>
> #define IXGBE_MAX_JUMBO_FRAME_SIZE 0x2600 /* Maximum Jumbo
> frame size. */
>
> diff --git a/drivers/net/ixgbe/ixgbe_rxtx.c b/drivers/net/ixgbe/ixgbe_rxtx.c
> index 9a79d18..0ef7fdf 100644
> --- a/drivers/net/ixgbe/ixgbe_rxtx.c
> +++ b/drivers/net/ixgbe/ixgbe_rxtx.c
> @@ -4879,10 +4879,14 @@ ixgbe_dev_rx_init(struct rte_eth_dev *dev)
> hlreg0 &= ~IXGBE_HLREG0_JUMBOEN;
>
> /*
> - * If loopback mode is configured for 82599, set LPBK bit.
> + * If loopback mode is configured, set LPBK bit.
> */
> - if (hw->mac.type == ixgbe_mac_82599EB &&
> - dev->data->dev_conf.lpbk_mode == IXGBE_LPBK_82599_TX_RX)
> + if ((hw->mac.type == ixgbe_mac_82599EB ||
> + hw->mac.type == ixgbe_mac_X540 ||
> + hw->mac.type == ixgbe_mac_X550 ||
> + hw->mac.type == ixgbe_mac_X550EM_x ||
> + hw->mac.type == ixgbe_mac_X550EM_a) &&
> + dev->data->dev_conf.lpbk_mode == IXGBE_LPBK_TX_RX)
> hlreg0 |= IXGBE_HLREG0_LPBK;
> else
> hlreg0 &= ~IXGBE_HLREG0_LPBK;
> @@ -5088,6 +5092,29 @@ ixgbe_setup_loopback_link_82599(struct ixgbe_hw
> *hw)
> msec_delay(50);
> }
>
> +/*
> + * Set up link loopback for X540 / X550 mode Tx->Rx.
> + */
> +static inline void __attribute__((cold))
> +ixgbe_setup_loopback_link_x540_x550(struct ixgbe_hw *hw) {
> + uint32_t macc;
> + PMD_INIT_FUNC_TRACE();
> +
> + /* datasheet 15.2.1: MACC.FLU = 1 (force link up) */
> + macc = IXGBE_READ_REG(hw, IXGBE_MACC);
> + macc |= IXGBE_MACC_FLU;
> + IXGBE_WRITE_REG(hw, IXGBE_MACC, macc);
> +
> + /* Restart link */
> + IXGBE_WRITE_REG(hw,
> + IXGBE_AUTOC,
> + IXGBE_AUTOC_LMS_10G_LINK_NO_AN | IXGBE_AUTOC_FLU);
> +
> + hw->mac.ops.release_swfw_sync(hw, IXGBE_GSSR_MAC_CSR_SM);
> + msec_delay(50);
> +}
> +
>
> /*
> * Start Transmit and Receive Units.
> @@ -5148,10 +5175,16 @@ ixgbe_dev_rxtx_start(struct rte_eth_dev *dev)
> rxctrl |= IXGBE_RXCTRL_RXEN;
> hw->mac.ops.enable_rx_dma(hw, rxctrl);
>
> - /* If loopback mode is enabled for 82599, set up the link accordingly */
> - if (hw->mac.type == ixgbe_mac_82599EB &&
> - dev->data->dev_conf.lpbk_mode == IXGBE_LPBK_82599_TX_RX)
> - ixgbe_setup_loopback_link_82599(hw);
> + /* If loopback mode is enabled, set up the link accordingly */
> + if (dev->data->dev_conf.lpbk_mode == IXGBE_LPBK_TX_RX) {
> + if (hw->mac.type == ixgbe_mac_82599EB)
> + ixgbe_setup_loopback_link_82599(hw);
> + else if (hw->mac.type == ixgbe_mac_X540 ||
> + hw->mac.type == ixgbe_mac_X550 ||
> + hw->mac.type == ixgbe_mac_X550EM_x ||
> + hw->mac.type == ixgbe_mac_X550EM_a)
> + ixgbe_setup_loopback_link_x540_x550(hw);
> + }
>
> #ifdef RTE_LIBRTE_SECURITY
> if ((dev->data->dev_conf.rxmode.offloads &
> --
> 2.10.2
> -----Original Message-----
> From: dev [mailto:dev-bounces@dpdk.org] On Behalf Of Julien Meunier
> Sent: Thursday, January 3, 2019 12:01 AM
> To: Ananyev, Konstantin <konstantin.ananyev@intel.com>; Lu, Wenzhuo
> <wenzhuo.lu@intel.com>
> Cc: dev@dpdk.org
> Subject: [dpdk-dev] [PATCH] net/ixgbe: add support of loopback for
> X540/X550
>
> Loopback mode is also supported on X540 and X550 NICs, according to their
> datasheet (section 15.2). The way to set it up is a little different of the 82599.
>
> Signed-off-by: Julien Meunier <julien.meunier@nokia.com>
> ---
> drivers/net/ixgbe/ixgbe_ethdev.c | 10 ++++++---
> drivers/net/ixgbe/ixgbe_ethdev.h | 5 ++---
> drivers/net/ixgbe/ixgbe_rxtx.c | 47
> ++++++++++++++++++++++++++++++++++------
> 3 files changed, 49 insertions(+), 13 deletions(-)
>
> diff --git a/drivers/net/ixgbe/ixgbe_ethdev.c
> b/drivers/net/ixgbe/ixgbe_ethdev.c
> index 7493110..7eb3303 100644
> --- a/drivers/net/ixgbe/ixgbe_ethdev.c
> +++ b/drivers/net/ixgbe/ixgbe_ethdev.c
> @@ -2652,9 +2652,13 @@ ixgbe_dev_start(struct rte_eth_dev *dev)
> goto error;
> }
>
> - /* Skip link setup if loopback mode is enabled for 82599. */
> - if (hw->mac.type == ixgbe_mac_82599EB &&
> - dev->data->dev_conf.lpbk_mode ==
> IXGBE_LPBK_82599_TX_RX)
> + /* Skip link setup if loopback mode is enabled. */
> + if ((hw->mac.type == ixgbe_mac_82599EB ||
> + hw->mac.type == ixgbe_mac_X540 ||
> + hw->mac.type == ixgbe_mac_X550 ||
> + hw->mac.type == ixgbe_mac_X550EM_x ||
> + hw->mac.type == ixgbe_mac_X550EM_a) &&
> + dev->data->dev_conf.lpbk_mode ==
> IXGBE_LPBK_TX_RX)
> goto skip_link_setup;
>
> if (ixgbe_is_sfp(hw) && hw->phy.multispeed_fiber) { diff --git
> a/drivers/net/ixgbe/ixgbe_ethdev.h b/drivers/net/ixgbe/ixgbe_ethdev.h
> index 565c69c..c60a697 100644
> --- a/drivers/net/ixgbe/ixgbe_ethdev.h
> +++ b/drivers/net/ixgbe/ixgbe_ethdev.h
> @@ -65,9 +65,8 @@
> #define IXGBE_QUEUE_ITR_INTERVAL_DEFAULT 500 /* 500us */
>
> /* Loopback operation modes */
> -/* 82599 specific loopback operation types */
> -#define IXGBE_LPBK_82599_NONE 0x0 /* Default value. Loopback is
> disabled. */
> -#define IXGBE_LPBK_82599_TX_RX 0x1 /* Tx->Rx loopback operation is
> enabled. */
> +#define IXGBE_LPBK_NONE 0x0 /* Default value. Loopback is disabled. */
> +#define IXGBE_LPBK_TX_RX 0x1 /* Tx->Rx loopback operation is enabled.
> +*/
>
> #define IXGBE_MAX_JUMBO_FRAME_SIZE 0x2600 /* Maximum Jumbo
> frame size. */
>
> diff --git a/drivers/net/ixgbe/ixgbe_rxtx.c b/drivers/net/ixgbe/ixgbe_rxtx.c
> index 9a79d18..0ef7fdf 100644
> --- a/drivers/net/ixgbe/ixgbe_rxtx.c
> +++ b/drivers/net/ixgbe/ixgbe_rxtx.c
> @@ -4879,10 +4879,14 @@ ixgbe_dev_rx_init(struct rte_eth_dev *dev)
> hlreg0 &= ~IXGBE_HLREG0_JUMBOEN;
>
> /*
> - * If loopback mode is configured for 82599, set LPBK bit.
> + * If loopback mode is configured, set LPBK bit.
> */
> - if (hw->mac.type == ixgbe_mac_82599EB &&
> - dev->data->dev_conf.lpbk_mode ==
> IXGBE_LPBK_82599_TX_RX)
> + if ((hw->mac.type == ixgbe_mac_82599EB ||
> + hw->mac.type == ixgbe_mac_X540 ||
> + hw->mac.type == ixgbe_mac_X550 ||
> + hw->mac.type == ixgbe_mac_X550EM_x ||
> + hw->mac.type == ixgbe_mac_X550EM_a) &&
> + dev->data->dev_conf.lpbk_mode ==
> IXGBE_LPBK_TX_RX)
> hlreg0 |= IXGBE_HLREG0_LPBK;
> else
> hlreg0 &= ~IXGBE_HLREG0_LPBK;
> @@ -5088,6 +5092,29 @@ ixgbe_setup_loopback_link_82599(struct
> ixgbe_hw *hw)
> msec_delay(50);
> }
>
> +/*
> + * Set up link loopback for X540 / X550 mode Tx->Rx.
> + */
> +static inline void __attribute__((cold))
> +ixgbe_setup_loopback_link_x540_x550(struct ixgbe_hw *hw) {
> + uint32_t macc;
> + PMD_INIT_FUNC_TRACE();
> +
> + /* datasheet 15.2.1: MACC.FLU = 1 (force link up) */
> + macc = IXGBE_READ_REG(hw, IXGBE_MACC);
> + macc |= IXGBE_MACC_FLU;
> + IXGBE_WRITE_REG(hw, IXGBE_MACC, macc);
> +
> + /* Restart link */
> + IXGBE_WRITE_REG(hw,
> + IXGBE_AUTOC,
> + IXGBE_AUTOC_LMS_10G_LINK_NO_AN |
> IXGBE_AUTOC_FLU);
> +
> + hw->mac.ops.release_swfw_sync(hw, IXGBE_GSSR_MAC_CSR_SM);
> + msec_delay(50);
> +}
> +
>
> /*
> * Start Transmit and Receive Units.
> @@ -5148,10 +5175,16 @@ ixgbe_dev_rxtx_start(struct rte_eth_dev *dev)
> rxctrl |= IXGBE_RXCTRL_RXEN;
> hw->mac.ops.enable_rx_dma(hw, rxctrl);
>
> - /* If loopback mode is enabled for 82599, set up the link accordingly
> */
> - if (hw->mac.type == ixgbe_mac_82599EB &&
> - dev->data->dev_conf.lpbk_mode ==
> IXGBE_LPBK_82599_TX_RX)
> - ixgbe_setup_loopback_link_82599(hw);
> + /* If loopback mode is enabled, set up the link accordingly */
> + if (dev->data->dev_conf.lpbk_mode == IXGBE_LPBK_TX_RX) {
> + if (hw->mac.type == ixgbe_mac_82599EB)
> + ixgbe_setup_loopback_link_82599(hw);
> + else if (hw->mac.type == ixgbe_mac_X540 ||
> + hw->mac.type == ixgbe_mac_X550 ||
> + hw->mac.type == ixgbe_mac_X550EM_x ||
> + hw->mac.type == ixgbe_mac_X550EM_a)
> + ixgbe_setup_loopback_link_x540_x550(hw);
Else
Return -1;
SHOULD we add some branch here?
In case some other NIC with configuration for tx->rx loop but pmd code do not support.
> + }
>
> #ifdef RTE_LIBRTE_SECURITY
> if ((dev->data->dev_conf.rxmode.offloads &
> --
> 2.10.2
Hi,
Mmm, you're right. However, as like for the 82599, the pmd skips the
link configuration, so, it should not enable the autoneg.
During my tests, I had a 10G connectivity, and I didn't notice any
problem. I used the DPDK application "test", with the test
pmd_perf_autotest.
Should I need to modify my code to be sure that autoneg is disabled (and
force it to 10G) ?
Thanks,
Best regards,
Julien Meunier
On 07/01/2019 07:53, Zhang, Qi Z wrote:
>
>
>> -----Original Message-----
>> From: dev [mailto:dev-bounces@dpdk.org] On Behalf Of Julien Meunier
>> Sent: Thursday, January 3, 2019 12:01 AM
>> To: Ananyev, Konstantin <konstantin.ananyev@intel.com>; Lu, Wenzhuo
>> <wenzhuo.lu@intel.com>
>> Cc: dev@dpdk.org
>> Subject: [dpdk-dev] [PATCH] net/ixgbe: add support of loopback for X540/X550
>>
>> Loopback mode is also supported on X540 and X550 NICs, according to their
>> datasheet (section 15.2). The way to set it up is a little different of the 82599.
>
> Thanks for enable this.
>
> one question is, Datasheet also mentioned that auto negotiation should be disabled
> but I didn't see any related change with it.
>
> Would you share more insight on this?
>
>>
>> Signed-off-by: Julien Meunier <julien.meunier@nokia.com>
>> ---
>> drivers/net/ixgbe/ixgbe_ethdev.c | 10 ++++++---
>> drivers/net/ixgbe/ixgbe_ethdev.h | 5 ++---
>> drivers/net/ixgbe/ixgbe_rxtx.c | 47
>> ++++++++++++++++++++++++++++++++++------
>> 3 files changed, 49 insertions(+), 13 deletions(-)
>>
>> diff --git a/drivers/net/ixgbe/ixgbe_ethdev.c
>> b/drivers/net/ixgbe/ixgbe_ethdev.c
>> index 7493110..7eb3303 100644
>> --- a/drivers/net/ixgbe/ixgbe_ethdev.c
>> +++ b/drivers/net/ixgbe/ixgbe_ethdev.c
>> @@ -2652,9 +2652,13 @@ ixgbe_dev_start(struct rte_eth_dev *dev)
>> goto error;
>> }
>>
>> - /* Skip link setup if loopback mode is enabled for 82599. */
>> - if (hw->mac.type == ixgbe_mac_82599EB &&
>> - dev->data->dev_conf.lpbk_mode == IXGBE_LPBK_82599_TX_RX)
>> + /* Skip link setup if loopback mode is enabled. */
>> + if ((hw->mac.type == ixgbe_mac_82599EB ||
>> + hw->mac.type == ixgbe_mac_X540 ||
>> + hw->mac.type == ixgbe_mac_X550 ||
>> + hw->mac.type == ixgbe_mac_X550EM_x ||
>> + hw->mac.type == ixgbe_mac_X550EM_a) &&
>> + dev->data->dev_conf.lpbk_mode == IXGBE_LPBK_TX_RX)
>> goto skip_link_setup;
>>
>> if (ixgbe_is_sfp(hw) && hw->phy.multispeed_fiber) { diff --git
>> a/drivers/net/ixgbe/ixgbe_ethdev.h b/drivers/net/ixgbe/ixgbe_ethdev.h
>> index 565c69c..c60a697 100644
>> --- a/drivers/net/ixgbe/ixgbe_ethdev.h
>> +++ b/drivers/net/ixgbe/ixgbe_ethdev.h
>> @@ -65,9 +65,8 @@
>> #define IXGBE_QUEUE_ITR_INTERVAL_DEFAULT 500 /* 500us */
>>
>> /* Loopback operation modes */
>> -/* 82599 specific loopback operation types */
>> -#define IXGBE_LPBK_82599_NONE 0x0 /* Default value. Loopback is disabled.
>> */
>> -#define IXGBE_LPBK_82599_TX_RX 0x1 /* Tx->Rx loopback operation is
>> enabled. */
>> +#define IXGBE_LPBK_NONE 0x0 /* Default value. Loopback is disabled. */
>> +#define IXGBE_LPBK_TX_RX 0x1 /* Tx->Rx loopback operation is enabled.
>> +*/
>>
>> #define IXGBE_MAX_JUMBO_FRAME_SIZE 0x2600 /* Maximum Jumbo
>> frame size. */
>>
>> diff --git a/drivers/net/ixgbe/ixgbe_rxtx.c b/drivers/net/ixgbe/ixgbe_rxtx.c
>> index 9a79d18..0ef7fdf 100644
>> --- a/drivers/net/ixgbe/ixgbe_rxtx.c
>> +++ b/drivers/net/ixgbe/ixgbe_rxtx.c
>> @@ -4879,10 +4879,14 @@ ixgbe_dev_rx_init(struct rte_eth_dev *dev)
>> hlreg0 &= ~IXGBE_HLREG0_JUMBOEN;
>>
>> /*
>> - * If loopback mode is configured for 82599, set LPBK bit.
>> + * If loopback mode is configured, set LPBK bit.
>> */
>> - if (hw->mac.type == ixgbe_mac_82599EB &&
>> - dev->data->dev_conf.lpbk_mode == IXGBE_LPBK_82599_TX_RX)
>> + if ((hw->mac.type == ixgbe_mac_82599EB ||
>> + hw->mac.type == ixgbe_mac_X540 ||
>> + hw->mac.type == ixgbe_mac_X550 ||
>> + hw->mac.type == ixgbe_mac_X550EM_x ||
>> + hw->mac.type == ixgbe_mac_X550EM_a) &&
>> + dev->data->dev_conf.lpbk_mode == IXGBE_LPBK_TX_RX)
>> hlreg0 |= IXGBE_HLREG0_LPBK;
>> else
>> hlreg0 &= ~IXGBE_HLREG0_LPBK;
>> @@ -5088,6 +5092,29 @@ ixgbe_setup_loopback_link_82599(struct ixgbe_hw
>> *hw)
>> msec_delay(50);
>> }
>>
>> +/*
>> + * Set up link loopback for X540 / X550 mode Tx->Rx.
>> + */
>> +static inline void __attribute__((cold))
>> +ixgbe_setup_loopback_link_x540_x550(struct ixgbe_hw *hw) {
>> + uint32_t macc;
>> + PMD_INIT_FUNC_TRACE();
>> +
>> + /* datasheet 15.2.1: MACC.FLU = 1 (force link up) */
>> + macc = IXGBE_READ_REG(hw, IXGBE_MACC);
>> + macc |= IXGBE_MACC_FLU;
>> + IXGBE_WRITE_REG(hw, IXGBE_MACC, macc);
>> +
>> + /* Restart link */
>> + IXGBE_WRITE_REG(hw,
>> + IXGBE_AUTOC,
>> + IXGBE_AUTOC_LMS_10G_LINK_NO_AN | IXGBE_AUTOC_FLU);
>> +
>> + hw->mac.ops.release_swfw_sync(hw, IXGBE_GSSR_MAC_CSR_SM);
>> + msec_delay(50);
>> +}
>> +
>>
>> /*
>> * Start Transmit and Receive Units.
>> @@ -5148,10 +5175,16 @@ ixgbe_dev_rxtx_start(struct rte_eth_dev *dev)
>> rxctrl |= IXGBE_RXCTRL_RXEN;
>> hw->mac.ops.enable_rx_dma(hw, rxctrl);
>>
>> - /* If loopback mode is enabled for 82599, set up the link accordingly */
>> - if (hw->mac.type == ixgbe_mac_82599EB &&
>> - dev->data->dev_conf.lpbk_mode == IXGBE_LPBK_82599_TX_RX)
>> - ixgbe_setup_loopback_link_82599(hw);
>> + /* If loopback mode is enabled, set up the link accordingly */
>> + if (dev->data->dev_conf.lpbk_mode == IXGBE_LPBK_TX_RX) {
>> + if (hw->mac.type == ixgbe_mac_82599EB)
>> + ixgbe_setup_loopback_link_82599(hw);
>> + else if (hw->mac.type == ixgbe_mac_X540 ||
>> + hw->mac.type == ixgbe_mac_X550 ||
>> + hw->mac.type == ixgbe_mac_X550EM_x ||
>> + hw->mac.type == ixgbe_mac_X550EM_a)
>> + ixgbe_setup_loopback_link_x540_x550(hw);
>> + }
>>
>> #ifdef RTE_LIBRTE_SECURITY
>> if ((dev->data->dev_conf.rxmode.offloads &
>> --
>> 2.10.2
>
Inline reply
On 07/01/2019 11:05, Zhao1, Wei wrote:
>
>
>> -----Original Message-----
>> From: dev [mailto:dev-bounces@dpdk.org] On Behalf Of Julien Meunier
>> Sent: Thursday, January 3, 2019 12:01 AM
>> To: Ananyev, Konstantin <konstantin.ananyev@intel.com>; Lu, Wenzhuo
>> <wenzhuo.lu@intel.com>
>> Cc: dev@dpdk.org
>> Subject: [dpdk-dev] [PATCH] net/ixgbe: add support of loopback for
>> X540/X550
>>
>> Loopback mode is also supported on X540 and X550 NICs, according to their
>> datasheet (section 15.2). The way to set it up is a little different of the 82599.
>>
>> Signed-off-by: Julien Meunier <julien.meunier@nokia.com>
[...]
>> diff --git a/drivers/net/ixgbe/ixgbe_rxtx.c b/drivers/net/ixgbe/ixgbe_rxtx.c
>> index 9a79d18..0ef7fdf 100644
>> --- a/drivers/net/ixgbe/ixgbe_rxtx.c
>> +++ b/drivers/net/ixgbe/ixgbe_rxtx.c
[...]
>> /*
>> * Start Transmit and Receive Units.
>> @@ -5148,10 +5175,16 @@ ixgbe_dev_rxtx_start(struct rte_eth_dev *dev)
>> rxctrl |= IXGBE_RXCTRL_RXEN;
>> hw->mac.ops.enable_rx_dma(hw, rxctrl);
>>
>> - /* If loopback mode is enabled for 82599, set up the link accordingly
>> */
>> - if (hw->mac.type == ixgbe_mac_82599EB &&
>> - dev->data->dev_conf.lpbk_mode ==
>> IXGBE_LPBK_82599_TX_RX)
>> - ixgbe_setup_loopback_link_82599(hw);
>> + /* If loopback mode is enabled, set up the link accordingly */
>> + if (dev->data->dev_conf.lpbk_mode == IXGBE_LPBK_TX_RX) {
>> + if (hw->mac.type == ixgbe_mac_82599EB)
>> + ixgbe_setup_loopback_link_82599(hw);
>> + else if (hw->mac.type == ixgbe_mac_X540 ||
>> + hw->mac.type == ixgbe_mac_X550 ||
>> + hw->mac.type == ixgbe_mac_X550EM_x ||
>> + hw->mac.type == ixgbe_mac_X550EM_a)
>> + ixgbe_setup_loopback_link_x540_x550(hw);
> Else
> Return -1;
>
> SHOULD we add some branch here?
> In case some other NIC with configuration for tx->rx loop but pmd code do not support.
My patch is iso-functional: if a user sets the lpbk_mode to 0x1
(IXGBE_LPBK_TX_RX), DPDK setups the TX -> RX loopback. Otherwise, it
ignores the configuration.
Please remember that lpbk_mode is specific to each PMD.
in rte_ethdev.h:
Loopback operation mode. By default the value is 0, meaning the
loopback mode is disabled. Read the datasheet of given ethernet
controller for details. The possible values of this field are
defined in implementation of each driver.
Other PMD can implement TX -> RX with other value.
Do I need to add more check around this LPBK ?
>
>> + }
>
>>
>> #ifdef RTE_LIBRTE_SECURITY
>> if ((dev->data->dev_conf.rxmode.offloads &
>> --
>> 2.10.2
>
Thanks,
Best regards,
Julien Meunier
Hi,Meunier, Julien
> -----Original Message-----
> From: Meunier, Julien (Nokia - FR/Paris-Saclay)
> [mailto:julien.meunier@nokia.com]
> Sent: Tuesday, January 8, 2019 12:05 AM
> To: Zhao1, Wei <wei.zhao1@intel.com>; Ananyev, Konstantin
> <konstantin.ananyev@intel.com>; Lu, Wenzhuo <wenzhuo.lu@intel.com>
> Cc: dev@dpdk.org
> Subject: Re: [dpdk-dev] [PATCH] net/ixgbe: add support of loopback for
> X540/X550
>
> Inline reply
>
> On 07/01/2019 11:05, Zhao1, Wei wrote:
> >
> >
> >> -----Original Message-----
> >> From: dev [mailto:dev-bounces@dpdk.org] On Behalf Of Julien Meunier
> >> Sent: Thursday, January 3, 2019 12:01 AM
> >> To: Ananyev, Konstantin <konstantin.ananyev@intel.com>; Lu, Wenzhuo
> >> <wenzhuo.lu@intel.com>
> >> Cc: dev@dpdk.org
> >> Subject: [dpdk-dev] [PATCH] net/ixgbe: add support of loopback for
> >> X540/X550
> >>
> >> Loopback mode is also supported on X540 and X550 NICs, according to
> >> their datasheet (section 15.2). The way to set it up is a little different of
> the 82599.
> >>
> >> Signed-off-by: Julien Meunier <julien.meunier@nokia.com>
> [...]
>
> >> diff --git a/drivers/net/ixgbe/ixgbe_rxtx.c
> >> b/drivers/net/ixgbe/ixgbe_rxtx.c index 9a79d18..0ef7fdf 100644
> >> --- a/drivers/net/ixgbe/ixgbe_rxtx.c
> >> +++ b/drivers/net/ixgbe/ixgbe_rxtx.c
>
> [...]
>
> >> /*
> >> * Start Transmit and Receive Units.
> >> @@ -5148,10 +5175,16 @@ ixgbe_dev_rxtx_start(struct rte_eth_dev
> *dev)
> >> rxctrl |= IXGBE_RXCTRL_RXEN;
> >> hw->mac.ops.enable_rx_dma(hw, rxctrl);
> >>
> >> - /* If loopback mode is enabled for 82599, set up the link accordingly
> >> */
> >> - if (hw->mac.type == ixgbe_mac_82599EB &&
> >> - dev->data->dev_conf.lpbk_mode ==
> >> IXGBE_LPBK_82599_TX_RX)
> >> - ixgbe_setup_loopback_link_82599(hw);
> >> + /* If loopback mode is enabled, set up the link accordingly */
> >> + if (dev->data->dev_conf.lpbk_mode == IXGBE_LPBK_TX_RX) {
> >> + if (hw->mac.type == ixgbe_mac_82599EB)
> >> + ixgbe_setup_loopback_link_82599(hw);
> >> + else if (hw->mac.type == ixgbe_mac_X540 ||
> >> + hw->mac.type == ixgbe_mac_X550 ||
> >> + hw->mac.type == ixgbe_mac_X550EM_x ||
> >> + hw->mac.type == ixgbe_mac_X550EM_a)
> >> + ixgbe_setup_loopback_link_x540_x550(hw);
> > Else
> > Return -1;
> >
> > SHOULD we add some branch here?
> > In case some other NIC with configuration for tx->rx loop but pmd code do
> not support.
>
> My patch is iso-functional: if a user sets the lpbk_mode to 0x1
> (IXGBE_LPBK_TX_RX), DPDK setups the TX -> RX loopback. Otherwise, it
> ignores the configuration.
>
> Please remember that lpbk_mode is specific to each PMD.
>
> in rte_ethdev.h:
> Loopback operation mode. By default the value is 0, meaning the
> loopback mode is disabled. Read the datasheet of given ethernet
> controller for details. The possible values of this field are
> defined in implementation of each driver.
>
> Other PMD can implement TX -> RX with other value.
>
> Do I need to add more check around this LPBK ?
Yes,
" Else
Return -1;
"
is need
My concern is such a case:
If some user is using 82598, and he set lpbk_mode to IXGBE_LPBK_TX_RX,
In fact Our IXGBE PMD do not support loopback mode for 82598, but we do not return error for that invalid configuration!!
So, we need some check for NIC type and error reminder.
>
> >
> >> + }
> >
> >>
> >> #ifdef RTE_LIBRTE_SECURITY
> >> if ((dev->data->dev_conf.rxmode.offloads &
> >> --
> >> 2.10.2
> >
>
> Thanks,
> Best regards,
> Julien Meunier
Hi, Meunier, Julien
> -----Original Message-----
> From: dev [mailto:dev-bounces@dpdk.org] On Behalf Of Meunier, Julien
> (Nokia - FR/Paris-Saclay)
> Sent: Monday, January 7, 2019 11:53 PM
> To: Zhang, Qi Z <qi.z.zhang@intel.com>; Ananyev, Konstantin
> <konstantin.ananyev@intel.com>; Lu, Wenzhuo <wenzhuo.lu@intel.com>
> Cc: dev@dpdk.org
> Subject: Re: [dpdk-dev] [PATCH] net/ixgbe: add support of loopback for
> X540/X550
>
> Hi,
>
> Mmm, you're right. However, as like for the 82599, the pmd skips the link
> configuration, so, it should not enable the autoneg.
>
> During my tests, I had a 10G connectivity, and I didn't notice any problem. I
> used the DPDK application "test", with the test pmd_perf_autotest.
It seems you are right, autoneg is done in function of ixgbe_setup_link()->........ ()
which call function ixgbe_setup_phy_link_speed_generic()->ixgbe_setup_phy_link ()->
ixgbe_setup_phy_link_generic (), do the work for Auto-Negotiation, but pmd code skip it.
But the bit C of Address 7.0 is initialized as 1 by default in datasheet, what pmd code skip is just the
Process of Auto-Negotiation, because we skip code of bellow In ixgbe_setup_phy_link_generic (), not disable bit 7.0.c.
So, you had better disable 7.0.c bit when mac loopback is enable.
"
/* Restart PHY auto-negotiation. */
hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_CONTROL,
IXGBE_MDIO_AUTO_NEG_DEV_TYPE, &autoneg_reg);
autoneg_reg |= IXGBE_MII_RESTART;
hw->phy.ops.write_reg(hw, IXGBE_MDIO_AUTO_NEG_CONTROL,
IXGBE_MDIO_AUTO_NEG_DEV_TYPE, autoneg_reg);
"
>
> Should I need to modify my code to be sure that autoneg is disabled (and
> force it to 10G) ?
>
> Thanks,
> Best regards,
> Julien Meunier
>
> On 07/01/2019 07:53, Zhang, Qi Z wrote:
> >
> >
> >> -----Original Message-----
> >> From: dev [mailto:dev-bounces@dpdk.org] On Behalf Of Julien Meunier
> >> Sent: Thursday, January 3, 2019 12:01 AM
> >> To: Ananyev, Konstantin <konstantin.ananyev@intel.com>; Lu, Wenzhuo
> >> <wenzhuo.lu@intel.com>
> >> Cc: dev@dpdk.org
> >> Subject: [dpdk-dev] [PATCH] net/ixgbe: add support of loopback for
> >> X540/X550
> >>
> >> Loopback mode is also supported on X540 and X550 NICs, according to
> >> their datasheet (section 15.2). The way to set it up is a little different of
> the 82599.
> >
> > Thanks for enable this.
> >
> > one question is, Datasheet also mentioned that auto negotiation should
> > be disabled but I didn't see any related change with it.
> >
> > Would you share more insight on this?
> >
> >>
> >> Signed-off-by: Julien Meunier <julien.meunier@nokia.com>
> >> ---
> >> drivers/net/ixgbe/ixgbe_ethdev.c | 10 ++++++---
> >> drivers/net/ixgbe/ixgbe_ethdev.h | 5 ++---
> >> drivers/net/ixgbe/ixgbe_rxtx.c | 47
> >> ++++++++++++++++++++++++++++++++++------
> >> 3 files changed, 49 insertions(+), 13 deletions(-)
> >>
> >> diff --git a/drivers/net/ixgbe/ixgbe_ethdev.c
> >> b/drivers/net/ixgbe/ixgbe_ethdev.c
> >> index 7493110..7eb3303 100644
> >> --- a/drivers/net/ixgbe/ixgbe_ethdev.c
> >> +++ b/drivers/net/ixgbe/ixgbe_ethdev.c
> >> @@ -2652,9 +2652,13 @@ ixgbe_dev_start(struct rte_eth_dev *dev)
> >> goto error;
> >> }
> >>
> >> - /* Skip link setup if loopback mode is enabled for 82599. */
> >> - if (hw->mac.type == ixgbe_mac_82599EB &&
> >> - dev->data->dev_conf.lpbk_mode ==
> IXGBE_LPBK_82599_TX_RX)
> >> + /* Skip link setup if loopback mode is enabled. */
> >> + if ((hw->mac.type == ixgbe_mac_82599EB ||
> >> + hw->mac.type == ixgbe_mac_X540 ||
> >> + hw->mac.type == ixgbe_mac_X550 ||
> >> + hw->mac.type == ixgbe_mac_X550EM_x ||
> >> + hw->mac.type == ixgbe_mac_X550EM_a) &&
> >> + dev->data->dev_conf.lpbk_mode ==
> IXGBE_LPBK_TX_RX)
> >> goto skip_link_setup;
> >>
> >> if (ixgbe_is_sfp(hw) && hw->phy.multispeed_fiber) { diff --git
> >> a/drivers/net/ixgbe/ixgbe_ethdev.h
> b/drivers/net/ixgbe/ixgbe_ethdev.h
> >> index 565c69c..c60a697 100644
> >> --- a/drivers/net/ixgbe/ixgbe_ethdev.h
> >> +++ b/drivers/net/ixgbe/ixgbe_ethdev.h
> >> @@ -65,9 +65,8 @@
> >> #define IXGBE_QUEUE_ITR_INTERVAL_DEFAULT 500 /* 500us */
> >>
> >> /* Loopback operation modes */
> >> -/* 82599 specific loopback operation types */
> >> -#define IXGBE_LPBK_82599_NONE 0x0 /* Default value. Loopback is
> disabled.
> >> */
> >> -#define IXGBE_LPBK_82599_TX_RX 0x1 /* Tx->Rx loopback operation is
> >> enabled. */
> >> +#define IXGBE_LPBK_NONE 0x0 /* Default value. Loopback is disabled.
> */
> >> +#define IXGBE_LPBK_TX_RX 0x1 /* Tx->Rx loopback operation is
> enabled.
> >> +*/
> >>
> >> #define IXGBE_MAX_JUMBO_FRAME_SIZE 0x2600 /* Maximum
> Jumbo
> >> frame size. */
> >>
> >> diff --git a/drivers/net/ixgbe/ixgbe_rxtx.c
> >> b/drivers/net/ixgbe/ixgbe_rxtx.c index 9a79d18..0ef7fdf 100644
> >> --- a/drivers/net/ixgbe/ixgbe_rxtx.c
> >> +++ b/drivers/net/ixgbe/ixgbe_rxtx.c
> >> @@ -4879,10 +4879,14 @@ ixgbe_dev_rx_init(struct rte_eth_dev *dev)
> >> hlreg0 &= ~IXGBE_HLREG0_JUMBOEN;
> >>
> >> /*
> >> - * If loopback mode is configured for 82599, set LPBK bit.
> >> + * If loopback mode is configured, set LPBK bit.
> >> */
> >> - if (hw->mac.type == ixgbe_mac_82599EB &&
> >> - dev->data->dev_conf.lpbk_mode ==
> IXGBE_LPBK_82599_TX_RX)
> >> + if ((hw->mac.type == ixgbe_mac_82599EB ||
> >> + hw->mac.type == ixgbe_mac_X540 ||
> >> + hw->mac.type == ixgbe_mac_X550 ||
> >> + hw->mac.type == ixgbe_mac_X550EM_x ||
> >> + hw->mac.type == ixgbe_mac_X550EM_a) &&
> >> + dev->data->dev_conf.lpbk_mode ==
> IXGBE_LPBK_TX_RX)
> >> hlreg0 |= IXGBE_HLREG0_LPBK;
> >> else
> >> hlreg0 &= ~IXGBE_HLREG0_LPBK;
> >> @@ -5088,6 +5092,29 @@ ixgbe_setup_loopback_link_82599(struct
> >> ixgbe_hw
> >> *hw)
> >> msec_delay(50);
> >> }
> >>
> >> +/*
> >> + * Set up link loopback for X540 / X550 mode Tx->Rx.
> >> + */
> >> +static inline void __attribute__((cold))
> >> +ixgbe_setup_loopback_link_x540_x550(struct ixgbe_hw *hw) {
> >> + uint32_t macc;
> >> + PMD_INIT_FUNC_TRACE();
> >> +
> >> + /* datasheet 15.2.1: MACC.FLU = 1 (force link up) */
> >> + macc = IXGBE_READ_REG(hw, IXGBE_MACC);
> >> + macc |= IXGBE_MACC_FLU;
> >> + IXGBE_WRITE_REG(hw, IXGBE_MACC, macc);
> >> +
> >> + /* Restart link */
> >> + IXGBE_WRITE_REG(hw,
> >> + IXGBE_AUTOC,
> >> + IXGBE_AUTOC_LMS_10G_LINK_NO_AN |
> IXGBE_AUTOC_FLU);
> >> +
> >> + hw->mac.ops.release_swfw_sync(hw, IXGBE_GSSR_MAC_CSR_SM);
> >> + msec_delay(50);
> >> +}
> >> +
> >>
> >> /*
> >> * Start Transmit and Receive Units.
> >> @@ -5148,10 +5175,16 @@ ixgbe_dev_rxtx_start(struct rte_eth_dev
> *dev)
> >> rxctrl |= IXGBE_RXCTRL_RXEN;
> >> hw->mac.ops.enable_rx_dma(hw, rxctrl);
> >>
> >> - /* If loopback mode is enabled for 82599, set up the link accordingly
> */
> >> - if (hw->mac.type == ixgbe_mac_82599EB &&
> >> - dev->data->dev_conf.lpbk_mode ==
> IXGBE_LPBK_82599_TX_RX)
> >> - ixgbe_setup_loopback_link_82599(hw);
> >> + /* If loopback mode is enabled, set up the link accordingly */
> >> + if (dev->data->dev_conf.lpbk_mode == IXGBE_LPBK_TX_RX) {
> >> + if (hw->mac.type == ixgbe_mac_82599EB)
> >> + ixgbe_setup_loopback_link_82599(hw);
> >> + else if (hw->mac.type == ixgbe_mac_X540 ||
> >> + hw->mac.type == ixgbe_mac_X550 ||
> >> + hw->mac.type == ixgbe_mac_X550EM_x ||
> >> + hw->mac.type == ixgbe_mac_X550EM_a)
> >> + ixgbe_setup_loopback_link_x540_x550(hw);
> >> + }
> >>
> >> #ifdef RTE_LIBRTE_SECURITY
> >> if ((dev->data->dev_conf.rxmode.offloads &
> >> --
> >> 2.10.2
> >
> -----Original Message-----
> From: Zhao1, Wei
> Sent: Tuesday, January 8, 2019 6:10 PM
> To: Meunier, Julien (Nokia - FR/Paris-Saclay) <julien.meunier@nokia.com>;
> Zhang, Qi Z <qi.z.zhang@intel.com>; Ananyev, Konstantin
> <konstantin.ananyev@intel.com>; Lu, Wenzhuo <wenzhuo.lu@intel.com>
> Cc: dev@dpdk.org
> Subject: RE: [dpdk-dev] [PATCH] net/ixgbe: add support of loopback for
> X540/X550
>
> Hi, Meunier, Julien
>
> > -----Original Message-----
> > From: dev [mailto:dev-bounces@dpdk.org] On Behalf Of Meunier, Julien
> > (Nokia - FR/Paris-Saclay)
> > Sent: Monday, January 7, 2019 11:53 PM
> > To: Zhang, Qi Z <qi.z.zhang@intel.com>; Ananyev, Konstantin
> > <konstantin.ananyev@intel.com>; Lu, Wenzhuo <wenzhuo.lu@intel.com>
> > Cc: dev@dpdk.org
> > Subject: Re: [dpdk-dev] [PATCH] net/ixgbe: add support of loopback for
> > X540/X550
> >
> > Hi,
> >
> > Mmm, you're right. However, as like for the 82599, the pmd skips the
> > link configuration, so, it should not enable the autoneg.
> >
> > During my tests, I had a 10G connectivity, and I didn't notice any
> > problem. I used the DPDK application "test", with the test pmd_perf_autotest.
>
> It seems you are right, autoneg is done in function of ixgbe_setup_link()->........ ()
> which call function
> ixgbe_setup_phy_link_speed_generic()->ixgbe_setup_phy_link ()->
> ixgbe_setup_phy_link_generic (), do the work for Auto-Negotiation, but pmd
> code skip it.
> But the bit C of Address 7.0 is initialized as 1 by default in datasheet, what pmd
> code skip is just the Process of Auto-Negotiation, because we skip code of bellow
> In ixgbe_setup_phy_link_generic (), not disable bit 7.0.c.
> So, you had better disable 7.0.c bit when mac loopback is enable.
>
> "
> /* Restart PHY auto-negotiation. */
> hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_CONTROL,
> IXGBE_MDIO_AUTO_NEG_DEV_TYPE, &autoneg_reg);
>
> autoneg_reg |= IXGBE_MII_RESTART;
>
> hw->phy.ops.write_reg(hw, IXGBE_MDIO_AUTO_NEG_CONTROL,
> IXGBE_MDIO_AUTO_NEG_DEV_TYPE, autoneg_reg); "
>
>
So, looks like PMD will not touch autoneg bit by default and we should not expected this bit always be on or off, because it can be changed by kernel driver before bind to dpdk.
probably a better solution could be
during dev_start if loopback is required, we disable the bit to make sure loopback works and remember its original status, and during dev_stop we do roll back if necessary
what do you think?
> > Should I need to modify my code to be sure that autoneg is disabled
> > (and force it to 10G) ?
> >
> > Thanks,
> > Best regards,
> > Julien Meunier
> >
> > On 07/01/2019 07:53, Zhang, Qi Z wrote:
> > >
> > >
> > >> -----Original Message-----
> > >> From: dev [mailto:dev-bounces@dpdk.org] On Behalf Of Julien Meunier
> > >> Sent: Thursday, January 3, 2019 12:01 AM
> > >> To: Ananyev, Konstantin <konstantin.ananyev@intel.com>; Lu, Wenzhuo
> > >> <wenzhuo.lu@intel.com>
> > >> Cc: dev@dpdk.org
> > >> Subject: [dpdk-dev] [PATCH] net/ixgbe: add support of loopback for
> > >> X540/X550
> > >>
> > >> Loopback mode is also supported on X540 and X550 NICs, according to
> > >> their datasheet (section 15.2). The way to set it up is a little
> > >> different of
> > the 82599.
> > >
> > > Thanks for enable this.
> > >
> > > one question is, Datasheet also mentioned that auto negotiation
> > > should be disabled but I didn't see any related change with it.
> > >
> > > Would you share more insight on this?
> > >
> > >>
> > >> Signed-off-by: Julien Meunier <julien.meunier@nokia.com>
> > >> ---
> > >> drivers/net/ixgbe/ixgbe_ethdev.c | 10 ++++++---
> > >> drivers/net/ixgbe/ixgbe_ethdev.h | 5 ++---
> > >> drivers/net/ixgbe/ixgbe_rxtx.c | 47
> > >> ++++++++++++++++++++++++++++++++++------
> > >> 3 files changed, 49 insertions(+), 13 deletions(-)
> > >>
> > >> diff --git a/drivers/net/ixgbe/ixgbe_ethdev.c
> > >> b/drivers/net/ixgbe/ixgbe_ethdev.c
> > >> index 7493110..7eb3303 100644
> > >> --- a/drivers/net/ixgbe/ixgbe_ethdev.c
> > >> +++ b/drivers/net/ixgbe/ixgbe_ethdev.c
> > >> @@ -2652,9 +2652,13 @@ ixgbe_dev_start(struct rte_eth_dev *dev)
> > >> goto error;
> > >> }
> > >>
> > >> - /* Skip link setup if loopback mode is enabled for 82599. */
> > >> - if (hw->mac.type == ixgbe_mac_82599EB &&
> > >> - dev->data->dev_conf.lpbk_mode ==
> > IXGBE_LPBK_82599_TX_RX)
> > >> + /* Skip link setup if loopback mode is enabled. */
> > >> + if ((hw->mac.type == ixgbe_mac_82599EB ||
> > >> + hw->mac.type == ixgbe_mac_X540 ||
> > >> + hw->mac.type == ixgbe_mac_X550 ||
> > >> + hw->mac.type == ixgbe_mac_X550EM_x ||
> > >> + hw->mac.type == ixgbe_mac_X550EM_a) &&
> > >> + dev->data->dev_conf.lpbk_mode ==
> > IXGBE_LPBK_TX_RX)
> > >> goto skip_link_setup;
> > >>
> > >> if (ixgbe_is_sfp(hw) && hw->phy.multispeed_fiber) { diff --git
> > >> a/drivers/net/ixgbe/ixgbe_ethdev.h
> > b/drivers/net/ixgbe/ixgbe_ethdev.h
> > >> index 565c69c..c60a697 100644
> > >> --- a/drivers/net/ixgbe/ixgbe_ethdev.h
> > >> +++ b/drivers/net/ixgbe/ixgbe_ethdev.h
> > >> @@ -65,9 +65,8 @@
> > >> #define IXGBE_QUEUE_ITR_INTERVAL_DEFAULT 500 /* 500us */
> > >>
> > >> /* Loopback operation modes */
> > >> -/* 82599 specific loopback operation types */
> > >> -#define IXGBE_LPBK_82599_NONE 0x0 /* Default value. Loopback is
> > disabled.
> > >> */
> > >> -#define IXGBE_LPBK_82599_TX_RX 0x1 /* Tx->Rx loopback operation
> > >> is enabled. */
> > >> +#define IXGBE_LPBK_NONE 0x0 /* Default value. Loopback is disabled.
> > */
> > >> +#define IXGBE_LPBK_TX_RX 0x1 /* Tx->Rx loopback operation is
> > enabled.
> > >> +*/
> > >>
> > >> #define IXGBE_MAX_JUMBO_FRAME_SIZE 0x2600 /* Maximum
> > Jumbo
> > >> frame size. */
> > >>
> > >> diff --git a/drivers/net/ixgbe/ixgbe_rxtx.c
> > >> b/drivers/net/ixgbe/ixgbe_rxtx.c index 9a79d18..0ef7fdf 100644
> > >> --- a/drivers/net/ixgbe/ixgbe_rxtx.c
> > >> +++ b/drivers/net/ixgbe/ixgbe_rxtx.c
> > >> @@ -4879,10 +4879,14 @@ ixgbe_dev_rx_init(struct rte_eth_dev *dev)
> > >> hlreg0 &= ~IXGBE_HLREG0_JUMBOEN;
> > >>
> > >> /*
> > >> - * If loopback mode is configured for 82599, set LPBK bit.
> > >> + * If loopback mode is configured, set LPBK bit.
> > >> */
> > >> - if (hw->mac.type == ixgbe_mac_82599EB &&
> > >> - dev->data->dev_conf.lpbk_mode ==
> > IXGBE_LPBK_82599_TX_RX)
> > >> + if ((hw->mac.type == ixgbe_mac_82599EB ||
> > >> + hw->mac.type == ixgbe_mac_X540 ||
> > >> + hw->mac.type == ixgbe_mac_X550 ||
> > >> + hw->mac.type == ixgbe_mac_X550EM_x ||
> > >> + hw->mac.type == ixgbe_mac_X550EM_a) &&
> > >> + dev->data->dev_conf.lpbk_mode ==
> > IXGBE_LPBK_TX_RX)
> > >> hlreg0 |= IXGBE_HLREG0_LPBK;
> > >> else
> > >> hlreg0 &= ~IXGBE_HLREG0_LPBK;
> > >> @@ -5088,6 +5092,29 @@ ixgbe_setup_loopback_link_82599(struct
> > >> ixgbe_hw
> > >> *hw)
> > >> msec_delay(50);
> > >> }
> > >>
> > >> +/*
> > >> + * Set up link loopback for X540 / X550 mode Tx->Rx.
> > >> + */
> > >> +static inline void __attribute__((cold))
> > >> +ixgbe_setup_loopback_link_x540_x550(struct ixgbe_hw *hw) {
> > >> + uint32_t macc;
> > >> + PMD_INIT_FUNC_TRACE();
> > >> +
> > >> + /* datasheet 15.2.1: MACC.FLU = 1 (force link up) */
> > >> + macc = IXGBE_READ_REG(hw, IXGBE_MACC);
> > >> + macc |= IXGBE_MACC_FLU;
> > >> + IXGBE_WRITE_REG(hw, IXGBE_MACC, macc);
> > >> +
> > >> + /* Restart link */
> > >> + IXGBE_WRITE_REG(hw,
> > >> + IXGBE_AUTOC,
> > >> + IXGBE_AUTOC_LMS_10G_LINK_NO_AN |
> > IXGBE_AUTOC_FLU);
> > >> +
> > >> + hw->mac.ops.release_swfw_sync(hw, IXGBE_GSSR_MAC_CSR_SM);
> > >> + msec_delay(50);
> > >> +}
> > >> +
> > >>
> > >> /*
> > >> * Start Transmit and Receive Units.
> > >> @@ -5148,10 +5175,16 @@ ixgbe_dev_rxtx_start(struct rte_eth_dev
> > *dev)
> > >> rxctrl |= IXGBE_RXCTRL_RXEN;
> > >> hw->mac.ops.enable_rx_dma(hw, rxctrl);
> > >>
> > >> - /* If loopback mode is enabled for 82599, set up the link accordingly
> > */
> > >> - if (hw->mac.type == ixgbe_mac_82599EB &&
> > >> - dev->data->dev_conf.lpbk_mode ==
> > IXGBE_LPBK_82599_TX_RX)
> > >> - ixgbe_setup_loopback_link_82599(hw);
> > >> + /* If loopback mode is enabled, set up the link accordingly */
> > >> + if (dev->data->dev_conf.lpbk_mode == IXGBE_LPBK_TX_RX) {
> > >> + if (hw->mac.type == ixgbe_mac_82599EB)
> > >> + ixgbe_setup_loopback_link_82599(hw);
> > >> + else if (hw->mac.type == ixgbe_mac_X540 ||
> > >> + hw->mac.type == ixgbe_mac_X550 ||
> > >> + hw->mac.type == ixgbe_mac_X550EM_x ||
> > >> + hw->mac.type == ixgbe_mac_X550EM_a)
> > >> + ixgbe_setup_loopback_link_x540_x550(hw);
> > >> + }
> > >>
> > >> #ifdef RTE_LIBRTE_SECURITY
> > >> if ((dev->data->dev_conf.rxmode.offloads &
> > >> --
> > >> 2.10.2
> > >
Hi Zhang, Qi Z / Zhao1, Wei,
Thanks for your comments.
I will try to submit this week a new pachset based on your
recommandation (check LPBK feature depending of the model + disable the
bit in the PHY register)
Best regards,
Julien Meunier
On 08/01/2019 13:39, Zhang, Qi Z wrote:
>
>
>> -----Original Message-----
>> From: Zhao1, Wei
>> Sent: Tuesday, January 8, 2019 6:10 PM
>> To: Meunier, Julien (Nokia - FR/Paris-Saclay) <julien.meunier@nokia.com>;
>> Zhang, Qi Z <qi.z.zhang@intel.com>; Ananyev, Konstantin
>> <konstantin.ananyev@intel.com>; Lu, Wenzhuo <wenzhuo.lu@intel.com>
>> Cc: dev@dpdk.org
>> Subject: RE: [dpdk-dev] [PATCH] net/ixgbe: add support of loopback for
>> X540/X550
>>
>> Hi, Meunier, Julien
>>
>>> -----Original Message-----
>>> From: dev [mailto:dev-bounces@dpdk.org] On Behalf Of Meunier, Julien
>>> (Nokia - FR/Paris-Saclay)
>>> Sent: Monday, January 7, 2019 11:53 PM
>>> To: Zhang, Qi Z <qi.z.zhang@intel.com>; Ananyev, Konstantin
>>> <konstantin.ananyev@intel.com>; Lu, Wenzhuo <wenzhuo.lu@intel.com>
>>> Cc: dev@dpdk.org
>>> Subject: Re: [dpdk-dev] [PATCH] net/ixgbe: add support of loopback for
>>> X540/X550
>>>
>>> Hi,
>>>
>>> Mmm, you're right. However, as like for the 82599, the pmd skips the
>>> link configuration, so, it should not enable the autoneg.
>>>
>>> During my tests, I had a 10G connectivity, and I didn't notice any
>>> problem. I used the DPDK application "test", with the test pmd_perf_autotest.
>>
>> It seems you are right, autoneg is done in function of ixgbe_setup_link()->........ ()
>> which call function
>> ixgbe_setup_phy_link_speed_generic()->ixgbe_setup_phy_link ()->
>> ixgbe_setup_phy_link_generic (), do the work for Auto-Negotiation, but pmd
>> code skip it.
>> But the bit C of Address 7.0 is initialized as 1 by default in datasheet, what pmd
>> code skip is just the Process of Auto-Negotiation, because we skip code of bellow
>> In ixgbe_setup_phy_link_generic (), not disable bit 7.0.c.
>> So, you had better disable 7.0.c bit when mac loopback is enable.
>>
>> "
>> /* Restart PHY auto-negotiation. */
>> hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_CONTROL,
>> IXGBE_MDIO_AUTO_NEG_DEV_TYPE, &autoneg_reg);
>>
>> autoneg_reg |= IXGBE_MII_RESTART;
>>
>> hw->phy.ops.write_reg(hw, IXGBE_MDIO_AUTO_NEG_CONTROL,
>> IXGBE_MDIO_AUTO_NEG_DEV_TYPE, autoneg_reg); "
>>
>>
>
> So, looks like PMD will not touch autoneg bit by default and we should not expected this bit always be on or off, because it can be changed by kernel driver before bind to dpdk.
>
> probably a better solution could be
>
> during dev_start if loopback is required, we disable the bit to make sure loopback works and remember its original status, and during dev_stop we do roll back if necessary
>
> what do you think?
>
>
>>> Should I need to modify my code to be sure that autoneg is disabled
>>> (and force it to 10G) ?
>>>
>>> Thanks,
>>> Best regards,
>>> Julien Meunier
>>>
>>> On 07/01/2019 07:53, Zhang, Qi Z wrote:
>>>>
>>>>
>>>>> -----Original Message-----
>>>>> From: dev [mailto:dev-bounces@dpdk.org] On Behalf Of Julien Meunier
>>>>> Sent: Thursday, January 3, 2019 12:01 AM
>>>>> To: Ananyev, Konstantin <konstantin.ananyev@intel.com>; Lu, Wenzhuo
>>>>> <wenzhuo.lu@intel.com>
>>>>> Cc: dev@dpdk.org
>>>>> Subject: [dpdk-dev] [PATCH] net/ixgbe: add support of loopback for
>>>>> X540/X550
>>>>>
>>>>> Loopback mode is also supported on X540 and X550 NICs, according to
>>>>> their datasheet (section 15.2). The way to set it up is a little
>>>>> different of
>>> the 82599.
>>>>
>>>> Thanks for enable this.
>>>>
>>>> one question is, Datasheet also mentioned that auto negotiation
>>>> should be disabled but I didn't see any related change with it.
>>>>
>>>> Would you share more insight on this?
>>>>
>>>>>
>>>>> Signed-off-by: Julien Meunier <julien.meunier@nokia.com>
>>>>> ---
>>>>> drivers/net/ixgbe/ixgbe_ethdev.c | 10 ++++++---
>>>>> drivers/net/ixgbe/ixgbe_ethdev.h | 5 ++---
>>>>> drivers/net/ixgbe/ixgbe_rxtx.c | 47
>>>>> ++++++++++++++++++++++++++++++++++------
>>>>> 3 files changed, 49 insertions(+), 13 deletions(-)
>>>>>
>>>>> diff --git a/drivers/net/ixgbe/ixgbe_ethdev.c
>>>>> b/drivers/net/ixgbe/ixgbe_ethdev.c
>>>>> index 7493110..7eb3303 100644
>>>>> --- a/drivers/net/ixgbe/ixgbe_ethdev.c
>>>>> +++ b/drivers/net/ixgbe/ixgbe_ethdev.c
>>>>> @@ -2652,9 +2652,13 @@ ixgbe_dev_start(struct rte_eth_dev *dev)
>>>>> goto error;
>>>>> }
>>>>>
>>>>> - /* Skip link setup if loopback mode is enabled for 82599. */
>>>>> - if (hw->mac.type == ixgbe_mac_82599EB &&
>>>>> - dev->data->dev_conf.lpbk_mode ==
>>> IXGBE_LPBK_82599_TX_RX)
>>>>> + /* Skip link setup if loopback mode is enabled. */
>>>>> + if ((hw->mac.type == ixgbe_mac_82599EB ||
>>>>> + hw->mac.type == ixgbe_mac_X540 ||
>>>>> + hw->mac.type == ixgbe_mac_X550 ||
>>>>> + hw->mac.type == ixgbe_mac_X550EM_x ||
>>>>> + hw->mac.type == ixgbe_mac_X550EM_a) &&
>>>>> + dev->data->dev_conf.lpbk_mode ==
>>> IXGBE_LPBK_TX_RX)
>>>>> goto skip_link_setup;
>>>>>
>>>>> if (ixgbe_is_sfp(hw) && hw->phy.multispeed_fiber) { diff --git
>>>>> a/drivers/net/ixgbe/ixgbe_ethdev.h
>>> b/drivers/net/ixgbe/ixgbe_ethdev.h
>>>>> index 565c69c..c60a697 100644
>>>>> --- a/drivers/net/ixgbe/ixgbe_ethdev.h
>>>>> +++ b/drivers/net/ixgbe/ixgbe_ethdev.h
>>>>> @@ -65,9 +65,8 @@
>>>>> #define IXGBE_QUEUE_ITR_INTERVAL_DEFAULT 500 /* 500us */
>>>>>
>>>>> /* Loopback operation modes */
>>>>> -/* 82599 specific loopback operation types */
>>>>> -#define IXGBE_LPBK_82599_NONE 0x0 /* Default value. Loopback is
>>> disabled.
>>>>> */
>>>>> -#define IXGBE_LPBK_82599_TX_RX 0x1 /* Tx->Rx loopback operation
>>>>> is enabled. */
>>>>> +#define IXGBE_LPBK_NONE 0x0 /* Default value. Loopback is disabled.
>>> */
>>>>> +#define IXGBE_LPBK_TX_RX 0x1 /* Tx->Rx loopback operation is
>>> enabled.
>>>>> +*/
>>>>>
>>>>> #define IXGBE_MAX_JUMBO_FRAME_SIZE 0x2600 /* Maximum
>>> Jumbo
>>>>> frame size. */
>>>>>
>>>>> diff --git a/drivers/net/ixgbe/ixgbe_rxtx.c
>>>>> b/drivers/net/ixgbe/ixgbe_rxtx.c index 9a79d18..0ef7fdf 100644
>>>>> --- a/drivers/net/ixgbe/ixgbe_rxtx.c
>>>>> +++ b/drivers/net/ixgbe/ixgbe_rxtx.c
>>>>> @@ -4879,10 +4879,14 @@ ixgbe_dev_rx_init(struct rte_eth_dev *dev)
>>>>> hlreg0 &= ~IXGBE_HLREG0_JUMBOEN;
>>>>>
>>>>> /*
>>>>> - * If loopback mode is configured for 82599, set LPBK bit.
>>>>> + * If loopback mode is configured, set LPBK bit.
>>>>> */
>>>>> - if (hw->mac.type == ixgbe_mac_82599EB &&
>>>>> - dev->data->dev_conf.lpbk_mode ==
>>> IXGBE_LPBK_82599_TX_RX)
>>>>> + if ((hw->mac.type == ixgbe_mac_82599EB ||
>>>>> + hw->mac.type == ixgbe_mac_X540 ||
>>>>> + hw->mac.type == ixgbe_mac_X550 ||
>>>>> + hw->mac.type == ixgbe_mac_X550EM_x ||
>>>>> + hw->mac.type == ixgbe_mac_X550EM_a) &&
>>>>> + dev->data->dev_conf.lpbk_mode ==
>>> IXGBE_LPBK_TX_RX)
>>>>> hlreg0 |= IXGBE_HLREG0_LPBK;
>>>>> else
>>>>> hlreg0 &= ~IXGBE_HLREG0_LPBK;
>>>>> @@ -5088,6 +5092,29 @@ ixgbe_setup_loopback_link_82599(struct
>>>>> ixgbe_hw
>>>>> *hw)
>>>>> msec_delay(50);
>>>>> }
>>>>>
>>>>> +/*
>>>>> + * Set up link loopback for X540 / X550 mode Tx->Rx.
>>>>> + */
>>>>> +static inline void __attribute__((cold))
>>>>> +ixgbe_setup_loopback_link_x540_x550(struct ixgbe_hw *hw) {
>>>>> + uint32_t macc;
>>>>> + PMD_INIT_FUNC_TRACE();
>>>>> +
>>>>> + /* datasheet 15.2.1: MACC.FLU = 1 (force link up) */
>>>>> + macc = IXGBE_READ_REG(hw, IXGBE_MACC);
>>>>> + macc |= IXGBE_MACC_FLU;
>>>>> + IXGBE_WRITE_REG(hw, IXGBE_MACC, macc);
>>>>> +
>>>>> + /* Restart link */
>>>>> + IXGBE_WRITE_REG(hw,
>>>>> + IXGBE_AUTOC,
>>>>> + IXGBE_AUTOC_LMS_10G_LINK_NO_AN |
>>> IXGBE_AUTOC_FLU);
>>>>> +
>>>>> + hw->mac.ops.release_swfw_sync(hw, IXGBE_GSSR_MAC_CSR_SM);
>>>>> + msec_delay(50);
>>>>> +}
>>>>> +
>>>>>
>>>>> /*
>>>>> * Start Transmit and Receive Units.
>>>>> @@ -5148,10 +5175,16 @@ ixgbe_dev_rxtx_start(struct rte_eth_dev
>>> *dev)
>>>>> rxctrl |= IXGBE_RXCTRL_RXEN;
>>>>> hw->mac.ops.enable_rx_dma(hw, rxctrl);
>>>>>
>>>>> - /* If loopback mode is enabled for 82599, set up the link accordingly
>>> */
>>>>> - if (hw->mac.type == ixgbe_mac_82599EB &&
>>>>> - dev->data->dev_conf.lpbk_mode ==
>>> IXGBE_LPBK_82599_TX_RX)
>>>>> - ixgbe_setup_loopback_link_82599(hw);
>>>>> + /* If loopback mode is enabled, set up the link accordingly */
>>>>> + if (dev->data->dev_conf.lpbk_mode == IXGBE_LPBK_TX_RX) {
>>>>> + if (hw->mac.type == ixgbe_mac_82599EB)
>>>>> + ixgbe_setup_loopback_link_82599(hw);
>>>>> + else if (hw->mac.type == ixgbe_mac_X540 ||
>>>>> + hw->mac.type == ixgbe_mac_X550 ||
>>>>> + hw->mac.type == ixgbe_mac_X550EM_x ||
>>>>> + hw->mac.type == ixgbe_mac_X550EM_a)
>>>>> + ixgbe_setup_loopback_link_x540_x550(hw);
>>>>> + }
>>>>>
>>>>> #ifdef RTE_LIBRTE_SECURITY
>>>>> if ((dev->data->dev_conf.rxmode.offloads &
>>>>> --
>>>>> 2.10.2
>>>>
> -----Original Message-----
> From: Zhang, Qi Z
> Sent: Tuesday, January 8, 2019 8:39 PM
> To: Zhao1, Wei <wei.zhao1@intel.com>; Meunier, Julien (Nokia - FR/Paris-
> Saclay) <julien.meunier@nokia.com>; Ananyev, Konstantin
> <konstantin.ananyev@intel.com>; Lu, Wenzhuo <wenzhuo.lu@intel.com>
> Cc: dev@dpdk.org
> Subject: RE: [dpdk-dev] [PATCH] net/ixgbe: add support of loopback for
> X540/X550
>
>
>
> > -----Original Message-----
> > From: Zhao1, Wei
> > Sent: Tuesday, January 8, 2019 6:10 PM
> > To: Meunier, Julien (Nokia - FR/Paris-Saclay)
> > <julien.meunier@nokia.com>; Zhang, Qi Z <qi.z.zhang@intel.com>;
> > Ananyev, Konstantin <konstantin.ananyev@intel.com>; Lu, Wenzhuo
> > <wenzhuo.lu@intel.com>
> > Cc: dev@dpdk.org
> > Subject: RE: [dpdk-dev] [PATCH] net/ixgbe: add support of loopback for
> > X540/X550
> >
> > Hi, Meunier, Julien
> >
> > > -----Original Message-----
> > > From: dev [mailto:dev-bounces@dpdk.org] On Behalf Of Meunier, Julien
> > > (Nokia - FR/Paris-Saclay)
> > > Sent: Monday, January 7, 2019 11:53 PM
> > > To: Zhang, Qi Z <qi.z.zhang@intel.com>; Ananyev, Konstantin
> > > <konstantin.ananyev@intel.com>; Lu, Wenzhuo <wenzhuo.lu@intel.com>
> > > Cc: dev@dpdk.org
> > > Subject: Re: [dpdk-dev] [PATCH] net/ixgbe: add support of loopback
> > > for
> > > X540/X550
> > >
> > > Hi,
> > >
> > > Mmm, you're right. However, as like for the 82599, the pmd skips the
> > > link configuration, so, it should not enable the autoneg.
> > >
> > > During my tests, I had a 10G connectivity, and I didn't notice any
> > > problem. I used the DPDK application "test", with the test
> pmd_perf_autotest.
> >
> > It seems you are right, autoneg is done in function of
> > ixgbe_setup_link()->........ () which call function
> > ixgbe_setup_phy_link_speed_generic()->ixgbe_setup_phy_link ()->
> > ixgbe_setup_phy_link_generic (), do the work for Auto-Negotiation,
> > but pmd code skip it.
> > But the bit C of Address 7.0 is initialized as 1 by default in
> > datasheet, what pmd code skip is just the Process of
> > Auto-Negotiation, because we skip code of bellow In
> ixgbe_setup_phy_link_generic (), not disable bit 7.0.c.
> > So, you had better disable 7.0.c bit when mac loopback is enable.
> >
> > "
> > /* Restart PHY auto-negotiation. */
> > hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_CONTROL,
> > IXGBE_MDIO_AUTO_NEG_DEV_TYPE,
> &autoneg_reg);
> >
> > autoneg_reg |= IXGBE_MII_RESTART;
> >
> > hw->phy.ops.write_reg(hw, IXGBE_MDIO_AUTO_NEG_CONTROL,
> > IXGBE_MDIO_AUTO_NEG_DEV_TYPE,
> autoneg_reg); "
> >
> >
>
> So, looks like PMD will not touch autoneg bit by default and we should not
> expected this bit always be on or off, because it can be changed by kernel
> driver before bind to dpdk.
>
> probably a better solution could be
>
> during dev_start if loopback is required, we disable the bit to make sure
> loopback works and remember its original status, and during dev_stop we do
> roll back if necessary
>
> what do you think?
Yes, agree with you.
>
>
> > > Should I need to modify my code to be sure that autoneg is disabled
> > > (and force it to 10G) ?
> > >
> > > Thanks,
> > > Best regards,
> > > Julien Meunier
> > >
> > > On 07/01/2019 07:53, Zhang, Qi Z wrote:
> > > >
> > > >
> > > >> -----Original Message-----
> > > >> From: dev [mailto:dev-bounces@dpdk.org] On Behalf Of Julien
> > > >> Meunier
> > > >> Sent: Thursday, January 3, 2019 12:01 AM
> > > >> To: Ananyev, Konstantin <konstantin.ananyev@intel.com>; Lu,
> > > >> Wenzhuo <wenzhuo.lu@intel.com>
> > > >> Cc: dev@dpdk.org
> > > >> Subject: [dpdk-dev] [PATCH] net/ixgbe: add support of loopback
> > > >> for
> > > >> X540/X550
> > > >>
> > > >> Loopback mode is also supported on X540 and X550 NICs, according
> > > >> to their datasheet (section 15.2). The way to set it up is a
> > > >> little different of
> > > the 82599.
> > > >
> > > > Thanks for enable this.
> > > >
> > > > one question is, Datasheet also mentioned that auto negotiation
> > > > should be disabled but I didn't see any related change with it.
> > > >
> > > > Would you share more insight on this?
> > > >
> > > >>
> > > >> Signed-off-by: Julien Meunier <julien.meunier@nokia.com>
> > > >> ---
> > > >> drivers/net/ixgbe/ixgbe_ethdev.c | 10 ++++++---
> > > >> drivers/net/ixgbe/ixgbe_ethdev.h | 5 ++---
> > > >> drivers/net/ixgbe/ixgbe_rxtx.c | 47
> > > >> ++++++++++++++++++++++++++++++++++------
> > > >> 3 files changed, 49 insertions(+), 13 deletions(-)
> > > >>
> > > >> diff --git a/drivers/net/ixgbe/ixgbe_ethdev.c
> > > >> b/drivers/net/ixgbe/ixgbe_ethdev.c
> > > >> index 7493110..7eb3303 100644
> > > >> --- a/drivers/net/ixgbe/ixgbe_ethdev.c
> > > >> +++ b/drivers/net/ixgbe/ixgbe_ethdev.c
> > > >> @@ -2652,9 +2652,13 @@ ixgbe_dev_start(struct rte_eth_dev *dev)
> > > >> goto error;
> > > >> }
> > > >>
> > > >> - /* Skip link setup if loopback mode is enabled for 82599. */
> > > >> - if (hw->mac.type == ixgbe_mac_82599EB &&
> > > >> - dev->data->dev_conf.lpbk_mode ==
> > > IXGBE_LPBK_82599_TX_RX)
> > > >> + /* Skip link setup if loopback mode is enabled. */
> > > >> + if ((hw->mac.type == ixgbe_mac_82599EB ||
> > > >> + hw->mac.type == ixgbe_mac_X540 ||
> > > >> + hw->mac.type == ixgbe_mac_X550 ||
> > > >> + hw->mac.type == ixgbe_mac_X550EM_x ||
> > > >> + hw->mac.type == ixgbe_mac_X550EM_a) &&
> > > >> + dev->data->dev_conf.lpbk_mode ==
> > > IXGBE_LPBK_TX_RX)
> > > >> goto skip_link_setup;
> > > >>
> > > >> if (ixgbe_is_sfp(hw) && hw->phy.multispeed_fiber) { diff --
> git
> > > >> a/drivers/net/ixgbe/ixgbe_ethdev.h
> > > b/drivers/net/ixgbe/ixgbe_ethdev.h
> > > >> index 565c69c..c60a697 100644
> > > >> --- a/drivers/net/ixgbe/ixgbe_ethdev.h
> > > >> +++ b/drivers/net/ixgbe/ixgbe_ethdev.h
> > > >> @@ -65,9 +65,8 @@
> > > >> #define IXGBE_QUEUE_ITR_INTERVAL_DEFAULT 500 /* 500us
> */
> > > >>
> > > >> /* Loopback operation modes */
> > > >> -/* 82599 specific loopback operation types */
> > > >> -#define IXGBE_LPBK_82599_NONE 0x0 /* Default value. Loopback is
> > > disabled.
> > > >> */
> > > >> -#define IXGBE_LPBK_82599_TX_RX 0x1 /* Tx->Rx loopback
> operation
> > > >> is enabled. */
> > > >> +#define IXGBE_LPBK_NONE 0x0 /* Default value. Loopback is
> disabled.
> > > */
> > > >> +#define IXGBE_LPBK_TX_RX 0x1 /* Tx->Rx loopback operation is
> > > enabled.
> > > >> +*/
> > > >>
> > > >> #define IXGBE_MAX_JUMBO_FRAME_SIZE 0x2600 /* Maximum
> > > Jumbo
> > > >> frame size. */
> > > >>
> > > >> diff --git a/drivers/net/ixgbe/ixgbe_rxtx.c
> > > >> b/drivers/net/ixgbe/ixgbe_rxtx.c index 9a79d18..0ef7fdf 100644
> > > >> --- a/drivers/net/ixgbe/ixgbe_rxtx.c
> > > >> +++ b/drivers/net/ixgbe/ixgbe_rxtx.c
> > > >> @@ -4879,10 +4879,14 @@ ixgbe_dev_rx_init(struct rte_eth_dev
> *dev)
> > > >> hlreg0 &= ~IXGBE_HLREG0_JUMBOEN;
> > > >>
> > > >> /*
> > > >> - * If loopback mode is configured for 82599, set LPBK bit.
> > > >> + * If loopback mode is configured, set LPBK bit.
> > > >> */
> > > >> - if (hw->mac.type == ixgbe_mac_82599EB &&
> > > >> - dev->data->dev_conf.lpbk_mode ==
> > > IXGBE_LPBK_82599_TX_RX)
> > > >> + if ((hw->mac.type == ixgbe_mac_82599EB ||
> > > >> + hw->mac.type == ixgbe_mac_X540 ||
> > > >> + hw->mac.type == ixgbe_mac_X550 ||
> > > >> + hw->mac.type == ixgbe_mac_X550EM_x ||
> > > >> + hw->mac.type == ixgbe_mac_X550EM_a) &&
> > > >> + dev->data->dev_conf.lpbk_mode ==
> > > IXGBE_LPBK_TX_RX)
> > > >> hlreg0 |= IXGBE_HLREG0_LPBK;
> > > >> else
> > > >> hlreg0 &= ~IXGBE_HLREG0_LPBK; @@ -5088,6
> +5092,29 @@
> > > >> ixgbe_setup_loopback_link_82599(struct
> > > >> ixgbe_hw
> > > >> *hw)
> > > >> msec_delay(50);
> > > >> }
> > > >>
> > > >> +/*
> > > >> + * Set up link loopback for X540 / X550 mode Tx->Rx.
> > > >> + */
> > > >> +static inline void __attribute__((cold))
> > > >> +ixgbe_setup_loopback_link_x540_x550(struct ixgbe_hw *hw) {
> > > >> + uint32_t macc;
> > > >> + PMD_INIT_FUNC_TRACE();
> > > >> +
> > > >> + /* datasheet 15.2.1: MACC.FLU = 1 (force link up) */
> > > >> + macc = IXGBE_READ_REG(hw, IXGBE_MACC);
> > > >> + macc |= IXGBE_MACC_FLU;
> > > >> + IXGBE_WRITE_REG(hw, IXGBE_MACC, macc);
> > > >> +
> > > >> + /* Restart link */
> > > >> + IXGBE_WRITE_REG(hw,
> > > >> + IXGBE_AUTOC,
> > > >> + IXGBE_AUTOC_LMS_10G_LINK_NO_AN |
> > > IXGBE_AUTOC_FLU);
> > > >> +
> > > >> + hw->mac.ops.release_swfw_sync(hw,
> IXGBE_GSSR_MAC_CSR_SM);
> > > >> + msec_delay(50);
> > > >> +}
> > > >> +
> > > >>
> > > >> /*
> > > >> * Start Transmit and Receive Units.
> > > >> @@ -5148,10 +5175,16 @@ ixgbe_dev_rxtx_start(struct rte_eth_dev
> > > *dev)
> > > >> rxctrl |= IXGBE_RXCTRL_RXEN;
> > > >> hw->mac.ops.enable_rx_dma(hw, rxctrl);
> > > >>
> > > >> - /* If loopback mode is enabled for 82599, set up the link accordingly
> > > */
> > > >> - if (hw->mac.type == ixgbe_mac_82599EB &&
> > > >> - dev->data->dev_conf.lpbk_mode ==
> > > IXGBE_LPBK_82599_TX_RX)
> > > >> - ixgbe_setup_loopback_link_82599(hw);
> > > >> + /* If loopback mode is enabled, set up the link accordingly */
> > > >> + if (dev->data->dev_conf.lpbk_mode == IXGBE_LPBK_TX_RX)
> {
> > > >> + if (hw->mac.type == ixgbe_mac_82599EB)
> > > >> + ixgbe_setup_loopback_link_82599(hw);
> > > >> + else if (hw->mac.type == ixgbe_mac_X540 ||
> > > >> + hw->mac.type == ixgbe_mac_X550 ||
> > > >> + hw->mac.type == ixgbe_mac_X550EM_x ||
> > > >> + hw->mac.type == ixgbe_mac_X550EM_a)
> > > >> + ixgbe_setup_loopback_link_x540_x550(hw);
> > > >> + }
> > > >>
> > > >> #ifdef RTE_LIBRTE_SECURITY
> > > >> if ((dev->data->dev_conf.rxmode.offloads &
> > > >> --
> > > >> 2.10.2
> > > >
@@ -2652,9 +2652,13 @@ ixgbe_dev_start(struct rte_eth_dev *dev)
goto error;
}
- /* Skip link setup if loopback mode is enabled for 82599. */
- if (hw->mac.type == ixgbe_mac_82599EB &&
- dev->data->dev_conf.lpbk_mode == IXGBE_LPBK_82599_TX_RX)
+ /* Skip link setup if loopback mode is enabled. */
+ if ((hw->mac.type == ixgbe_mac_82599EB ||
+ hw->mac.type == ixgbe_mac_X540 ||
+ hw->mac.type == ixgbe_mac_X550 ||
+ hw->mac.type == ixgbe_mac_X550EM_x ||
+ hw->mac.type == ixgbe_mac_X550EM_a) &&
+ dev->data->dev_conf.lpbk_mode == IXGBE_LPBK_TX_RX)
goto skip_link_setup;
if (ixgbe_is_sfp(hw) && hw->phy.multispeed_fiber) {
@@ -65,9 +65,8 @@
#define IXGBE_QUEUE_ITR_INTERVAL_DEFAULT 500 /* 500us */
/* Loopback operation modes */
-/* 82599 specific loopback operation types */
-#define IXGBE_LPBK_82599_NONE 0x0 /* Default value. Loopback is disabled. */
-#define IXGBE_LPBK_82599_TX_RX 0x1 /* Tx->Rx loopback operation is enabled. */
+#define IXGBE_LPBK_NONE 0x0 /* Default value. Loopback is disabled. */
+#define IXGBE_LPBK_TX_RX 0x1 /* Tx->Rx loopback operation is enabled. */
#define IXGBE_MAX_JUMBO_FRAME_SIZE 0x2600 /* Maximum Jumbo frame size. */
@@ -4879,10 +4879,14 @@ ixgbe_dev_rx_init(struct rte_eth_dev *dev)
hlreg0 &= ~IXGBE_HLREG0_JUMBOEN;
/*
- * If loopback mode is configured for 82599, set LPBK bit.
+ * If loopback mode is configured, set LPBK bit.
*/
- if (hw->mac.type == ixgbe_mac_82599EB &&
- dev->data->dev_conf.lpbk_mode == IXGBE_LPBK_82599_TX_RX)
+ if ((hw->mac.type == ixgbe_mac_82599EB ||
+ hw->mac.type == ixgbe_mac_X540 ||
+ hw->mac.type == ixgbe_mac_X550 ||
+ hw->mac.type == ixgbe_mac_X550EM_x ||
+ hw->mac.type == ixgbe_mac_X550EM_a) &&
+ dev->data->dev_conf.lpbk_mode == IXGBE_LPBK_TX_RX)
hlreg0 |= IXGBE_HLREG0_LPBK;
else
hlreg0 &= ~IXGBE_HLREG0_LPBK;
@@ -5088,6 +5092,29 @@ ixgbe_setup_loopback_link_82599(struct ixgbe_hw *hw)
msec_delay(50);
}
+/*
+ * Set up link loopback for X540 / X550 mode Tx->Rx.
+ */
+static inline void __attribute__((cold))
+ixgbe_setup_loopback_link_x540_x550(struct ixgbe_hw *hw)
+{
+ uint32_t macc;
+ PMD_INIT_FUNC_TRACE();
+
+ /* datasheet 15.2.1: MACC.FLU = 1 (force link up) */
+ macc = IXGBE_READ_REG(hw, IXGBE_MACC);
+ macc |= IXGBE_MACC_FLU;
+ IXGBE_WRITE_REG(hw, IXGBE_MACC, macc);
+
+ /* Restart link */
+ IXGBE_WRITE_REG(hw,
+ IXGBE_AUTOC,
+ IXGBE_AUTOC_LMS_10G_LINK_NO_AN | IXGBE_AUTOC_FLU);
+
+ hw->mac.ops.release_swfw_sync(hw, IXGBE_GSSR_MAC_CSR_SM);
+ msec_delay(50);
+}
+
/*
* Start Transmit and Receive Units.
@@ -5148,10 +5175,16 @@ ixgbe_dev_rxtx_start(struct rte_eth_dev *dev)
rxctrl |= IXGBE_RXCTRL_RXEN;
hw->mac.ops.enable_rx_dma(hw, rxctrl);
- /* If loopback mode is enabled for 82599, set up the link accordingly */
- if (hw->mac.type == ixgbe_mac_82599EB &&
- dev->data->dev_conf.lpbk_mode == IXGBE_LPBK_82599_TX_RX)
- ixgbe_setup_loopback_link_82599(hw);
+ /* If loopback mode is enabled, set up the link accordingly */
+ if (dev->data->dev_conf.lpbk_mode == IXGBE_LPBK_TX_RX) {
+ if (hw->mac.type == ixgbe_mac_82599EB)
+ ixgbe_setup_loopback_link_82599(hw);
+ else if (hw->mac.type == ixgbe_mac_X540 ||
+ hw->mac.type == ixgbe_mac_X550 ||
+ hw->mac.type == ixgbe_mac_X550EM_x ||
+ hw->mac.type == ixgbe_mac_X550EM_a)
+ ixgbe_setup_loopback_link_x540_x550(hw);
+ }
#ifdef RTE_LIBRTE_SECURITY
if ((dev->data->dev_conf.rxmode.offloads &