[12/27] event/dlb: add the PMD's public interfaces

diff --git a/drivers/event/dlb/rte_pmd_dlb.c b/drivers/event/dlb/rte_pmd_dlb.c
new file mode 100644
index 000000000..11f0d66cd
--- /dev/null
+++ b/drivers/event/dlb/rte_pmd_dlb.c
@@ -0,0 +1,39 @@ 
+/* SPDX-License-Identifier: BSD-3-Clause
+ * Copyright(c) 2020 Intel Corporation
+ */
+
+#include "rte_eventdev.h"
+#include "rte_eventdev_pmd.h"
+
+#include "rte_pmd_dlb.h"
+#include "dlb_priv.h"
+#include "dlb_inline_fns.h"
+
+int
+rte_pmd_dlb_set_token_pop_mode(uint8_t dev_id,
+				uint8_t port_id,
+				enum dlb_token_pop_mode mode)
+{
+	struct dlb_eventdev *dlb;
+	struct rte_eventdev *dev;
+
+	RTE_EVENTDEV_VALID_DEVID_OR_ERR_RET(dev_id, -EINVAL);
+	dev = &rte_eventdevs[dev_id];
+
+	dlb = dlb_pmd_priv(dev);
+
+	if (mode >= NUM_TOKEN_POP_MODES)
+		return -EINVAL;
+
+	/* The event device must be configured, but not yet started */
+	if (!dlb->configured || dlb->run_state != DLB_RUN_STATE_STOPPED)
+		return -EINVAL;
+
+	/* The token pop mode must be set before configuring the port */
+	if (port_id >= dlb->num_ports || dlb->ev_ports[port_id].setup_done)
+		return -EINVAL;
+
+	dlb->ev_ports[port_id].qm_port.token_pop_mode = mode;
+
+	return 0;
+}
diff --git a/drivers/event/dlb/rte_pmd_dlb.h b/drivers/event/dlb/rte_pmd_dlb.h
new file mode 100644
index 000000000..1b637def6
--- /dev/null
+++ b/drivers/event/dlb/rte_pmd_dlb.h
@@ -0,0 +1,69 @@ 
+/* SPDX-License-Identifier: BSD-3-Clause
+ * Copyright(c) 2019-2020 Intel Corporation
+ */
+
+/*!
+ *  @file      rte_pmd_dlb.h
+ *
+ *  @brief     DLB PMD-specific functions
+ */
+
+#ifndef _RTE_PMD_DLB_H_
+#define _RTE_PMD_DLB_H_
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+#include <stdint.h>
+
+/**
+ * Selects the token pop mode for an DLB port.
+ */
+enum dlb_token_pop_mode {
+	/* Pop the CQ tokens immediately after dequeueing. */
+	AUTO_POP,
+	/* Pop CQ tokens after (dequeue_depth - 1) events are released.
+	 * Supported on load-balanced ports only.
+	 */
+	DELAYED_POP,
+	/* Pop the CQ tokens during next dequeue operation. */
+	DEFERRED_POP,
+
+	/* NUM_TOKEN_POP_MODES must be last */
+	NUM_TOKEN_POP_MODES
+};
+
+/*!
+ * Configure the token pop mode for an DLB port. By default, all ports use
+ * AUTO_POP. This function must be called before calling rte_event_port_setup()
+ * for the port, but after calling rte_event_dev_configure().
+ *
+ * @note
+ *    The defer_sched vdev arg, which configures all load-balanced ports with
+ *    dequeue_depth == 1 for DEFERRED_POP mode, takes precedence over this
+ *    function.
+ *
+ * @param dev_id
+ *    The identifier of the event device.
+ * @param port_id
+ *    The identifier of the event port.
+ * @param mode
+ *    The token pop mode.
+ *
+ * @return
+ * - 0: Success
+ * - EINVAL: Invalid dev_id, port_id, or mode
+ * - EINVAL: The DLB is not configured, is already running, or the port is
+ *   already setup
+ */
+
+int
+rte_pmd_dlb_set_token_pop_mode(uint8_t dev_id,
+				uint8_t port_id,
+				enum dlb_token_pop_mode mode);
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* _RTE_PMD_DLB_H_ */
diff --git a/drivers/event/dlb/rte_pmd_dlb_event_version.map b/drivers/event/dlb/rte_pmd_dlb_event_version.map
new file mode 100644
index 000000000..8b1c796de
--- /dev/null
+++ b/drivers/event/dlb/rte_pmd_dlb_event_version.map
@@ -0,0 +1,6 @@ 
+DPDK_20.08 {
+	global:
+
+	rte_pmd_dlb_set_token_pop_mode;
+	local: *;
+};